Re: NM-0.7 hang on at "supplicant interface is now in state 2 (from 1)"

["Yung-Ting Chang" <foreverr gmail com>]

Thank a lot for your reply.

Like I said.
I tried to run nm-applet by myself but still doesn't work and
shown the following message:

NetworkManager: <info>  starting...
NetworkManager: <info>  eth0: Device is fully-supported using driver 'sky2'.
NetworkManager: <info>  (eth0): exporting device as
/org/freedesktop/NetworkManager/Device/2
NetworkManager: <info>  Now managing wired Ethernet (802.3) device 'eth0'.
NetworkManager: <info>  Bringing up device eth0
NetworkManager: <info>  Deactivating device eth0.
NetworkManager: <info>  eth1: Device is fully-supported using driver 'bcm43xx'.
NetworkManager: <info>  (eth1): exporting device as
/org/freedesktop/NetworkManager/Device/3
NetworkManager: <info>  Now managing wireless (802.11) device 'eth1'.
NetworkManager: <info>  Bringing up device eth1
NetworkManager: <info>  Deactivating device eth1.
NetworkManager: <info>  (eth0) supplicant interface is now in state 2 (from 1).
NetworkManager: <info>  (eth1) supplicant interface is now in state 2 (from 1).
NetworkManager: <info>  SWITCH: no current connection, found better
connection 'Auto Ethernet (eth0)'.
NetworkManager: <info>  Activating device eth0
NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
Prepare) scheduled...
NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
Prepare) started...
NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
Configure) scheduled...
NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
Prepare) complete.
NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
Configure) starting...
NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
Configure) successful.
NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
Start) scheduled.
NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
Configure) complete.
NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
Start) started...
NetworkManager: <info>  Activation (eth0) Beginning DHCP transaction.
Internet Systems Consortium DHCP Client V3.0.5
Copyright 2004-2006 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

NetworkManager: <info>  dhclient started with pid 17573
NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
Start) complete.
Error: Could not acquire the NM DHCP client service. Message:
(org.freedesktop.DBus.Error.AccessDenied) Connection ":1.41" is not
allowed to own the service "org.freedesktop.nm_dhcp_client" due to
security policies in the configuration file
Listening on LPF/eth0/00:16:d3:5b:d2:ae
Sending on   LPF/eth0/00:16:d3:5b:d2:ae
Sending on   Socket/fallback
DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
DHCPOFFER from 10.36.251.1
DHCPREQUEST on eth0 to 255.255.255.255 port 67
DHCPACK from 10.36.251.1
Error: Could not acquire the NM DHCP client service. Message:
(org.freedesktop.DBus.Error.AccessDenied) Connection ":1.42" is not
allowed to own the service "org.freedesktop.nm_dhcp_client" due to
security policies in the configuration file
bound to 10.36.253.137 -- renewal in 128334 seconds.

how should I fix the nm_dhcp_client dbus problem?
What should I do?

Thank you for helping me.

Sincerely,

Richard Chang



2007/11/19, Yung-Ting Chang <foreverr gmail com>:
> Sorry for bothering all guys.
> I tried to svn check out Networkmanager-0.7 and nm-applet from SVN
> (revision 3095)
> i followed some information from mail-list and following is what's i did
>
>
> and following is the wpa_supplicant message:
>
> #wpa_supplicant -u -dd
> Providing DBus service 'fi.epitest.hostap.WPASupplicant'.
> Initializing interface 'eth0' conf 'N/A' driver 'wired' ctrl_interface
> 'N/A' bridge 'N/A'
> Initializing interface (2) 'eth0'
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> EAPOL: SUPP_BE entering state INITIALIZE
> EAP: EAP entering state DISABLED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> wpa_driver_wired_init: Added multicast membership with packet socket
> Own MAC address: 00:16:d3:5b:d2:ae
> Setting scan request: 0 sec 100000 usec
> Added interface eth0
> Using wired driver - overriding ap_scan configuration
> Initializing interface 'eth1' conf 'N/A' driver 'wext' ctrl_interface
> 'N/A' bridge 'N/A'
> Initializing interface (2) 'eth1'
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> EAPOL: SUPP_BE entering state INITIALIZE
> EAP: EAP entering state DISABLED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> SIOCSIFFLAGS: No such device
> Could not set interface 'eth1' UP
> SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf
>  capabilities: key_mgmt 0xf enc 0xf
> WEXT: Operstate: linkmode=1, operstate=5
> Own MAC address: 00:19:7e:8c:05:b0
> wpa_driver_wext_set_wpa
> wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_countermeasures
> wpa_driver_wext_set_drop_unencrypted
> Setting scan request: 1 sec 100000 usec
> Added interface eth1
> RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
> Wireless event: cmd=0x8b06 len=8
> RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
> Wireless event: cmd=0x8b1a len=8
> RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
> Wireless event: cmd=0x8b2a len=8
> l2_packet_receive - recvfrom: Network is down
> Setting scan request: 0 sec 0 usec
> State: DISCONNECTED -> SCANNING
> Starting AP scan (broadcast SSID)
> Trying to get current scan results first without requesting a new scan
> to speed up initial association
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> No suitable AP found.
> Setting scan request: 0 sec 0 usec
> No enabled networks - do not scan
> State: SCANNING -> INACTIVE
> Received 0 bytes of scan results (0 BSSes)
> Scan results: 0
> Ignore event for foreign ifindex 2
> ----------------
>
> #NetworkManager --no-daemon
>
> NetworkManager: <info>  starting...
> NetworkManager: <info>  eth0: Device is fully-supported using driver 'sky2'.
> NetworkManager: <info>  (eth0): exporting device as
> /org/freedesktop/NetworkManager/Device/2
> NetworkManager: <info>  Now managing wired Ethernet (802.3) device 'eth0'.
> NetworkManager: <info>  Bringing down device eth0
> NetworkManager: <info>  Bringing up device eth0
> NetworkManager: <info>  Deactivating device eth0.
> NetworkManager: <info>  eth1: Device is fully-supported using driver 'bcm43xx'.
> NetworkManager: <info>  (eth1): exporting device as
> /org/freedesktop/NetworkManager/Device/3
> NetworkManager: <info>  Now managing wireless (802.11) device 'eth1'.
> NetworkManager: <info>  Bringing down device eth1
> NetworkManager: <info>  Bringing up device eth1
> NetworkManager: <info>  Deactivating device eth1.
> NetworkManager: <info>  (eth0) supplicant interface is now in state 2 (from 1).
> NetworkManager: <info>  (eth1) supplicant interface is now in state 2 (from 1).
> -----------------
>
>
> Then the NetworkManager hang on here.
> Is there any advise for me to solve this? thank you a lot!
> should I run nm-applet by myself?
> i ever tried to run nm-applet by myself but still doesn't work and
> shown the following message:
>
> NetworkManager: <info>  starting...
> NetworkManager: <info>  eth0: Device is fully-supported using driver 'sky2'.
> NetworkManager: <info>  (eth0): exporting device as
> /org/freedesktop/NetworkManager/Device/2
> NetworkManager: <info>  Now managing wired Ethernet (802.3) device 'eth0'.
> NetworkManager: <info>  Bringing up device eth0
> NetworkManager: <info>  Deactivating device eth0.
> NetworkManager: <info>  eth1: Device is fully-supported using driver 'bcm43xx'.
> NetworkManager: <info>  (eth1): exporting device as
> /org/freedesktop/NetworkManager/Device/3
> NetworkManager: <info>  Now managing wireless (802.11) device 'eth1'.
> NetworkManager: <info>  Bringing up device eth1
> NetworkManager: <info>  Deactivating device eth1.
> NetworkManager: <info>  (eth0) supplicant interface is now in state 2 (from 1).
> NetworkManager: <info>  (eth1) supplicant interface is now in state 2 (from 1).
> NetworkManager: <info>  SWITCH: no current connection, found better
> connection 'Auto Ethernet (eth0)'.
> NetworkManager: <info>  Activating device eth0
> NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
> Prepare) scheduled...
> NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
> Prepare) started...
> NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
> Configure) scheduled...
> NetworkManager: <info>  Activation (eth0) Stage 1 of 5 (Device
> Prepare) complete.
> NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
> Configure) starting...
> NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
> Configure) successful.
> NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
> Start) scheduled.
> NetworkManager: <info>  Activation (eth0) Stage 2 of 5 (Device
> Configure) complete.
> NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
> Start) started...
> NetworkManager: <info>  Activation (eth0) Beginning DHCP transaction.
> Internet Systems Consortium DHCP Client V3.0.5
> Copyright 2004-2006 Internet Systems Consortium.
> All rights reserved.
> For info, please visit http://www.isc.org/sw/dhcp/
>
> NetworkManager: <info>  dhclient started with pid 17573
> NetworkManager: <info>  Activation (eth0) Stage 3 of 5 (IP Configure
> Start) complete.
> Error: Could not acquire the NM DHCP client service. Message:
> (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.41" is not
> allowed to own the service "org.freedesktop.nm_dhcp_client" due to
> security policies in the configuration file
> Listening on LPF/eth0/00:16:d3:5b:d2:ae
> Sending on   LPF/eth0/00:16:d3:5b:d2:ae
> Sending on   Socket/fallback
> DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
> DHCPOFFER from 10.36.251.1
> DHCPREQUEST on eth0 to 255.255.255.255 port 67
> DHCPACK from 10.36.251.1
> Error: Could not acquire the NM DHCP client service. Message:
> (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.42" is not
> allowed to own the service "org.freedesktop.nm_dhcp_client" due to
> security policies in the configuration file
> bound to 10.36.253.137 -- renewal in 128334 seconds.
> -----------
>
> here is my device info:
> wpa_supplicant v0.5.8
>
> NetworkManager Tool
>
> State: disconnected
>
> - Device: eth0 ----------------------------------------------------------------
>  Type:              Wired
>  Driver:            sky2
>  Active:            no
>  HW Address:        XX:XX:XX:XX:XX:XX
>
>  Capabilities:
>    Supported:       yes
>    Carrier Detect:  yes
>    Speed:           100 Mb/s
>
>  Wired Settings
>
>
> - Device: eth1 ----------------------------------------------------------------
>  Type:              802.11 Wireless
>  Driver:            bcm43xx
>  Active:            no
>  HW Address:        XX:XX:XX:XX:XX:XX
>
>  Capabilities:
>    Supported:       yes
>
>  Wireless Settings
>    WEP Encryption:  yes
>    WPA Encryption:  yes
>    WPA2 Encryption: yes
>
> thank you for your help
>
> Richard Chang.
>