Re: [Evolution] evo .10, libunicode, and compile problems

[Spacemonkey <spacemonkey spacemonkeylabs com>]

Tried it, without success.  :'"

Even removed the ambiguous "--with-pisock" as I'm not sure its related
to the pilot stuff.  Still no good.  config.log indicates that
pilot-link is found (and is an acceptable version), so I'm really at a
dead-end here.

Another question:  is it true that the pilot stuff is not included in
the snapshots (including SRPMS)?  Am I trying to compile something that
is just not there?

On 06 Apr 2001 00:12:52 +0930, Not Zed wrote:
> try
>
> rm -rf `find . -name .deps`
>
> To reset the dependency files.
>
>
> On 05 Apr 2001 15:56:50 +0200, Spacemonkey wrote:
> > Hi Ross,
> >
> > You got me past the libunicode(-devel) problem.  Thanks!  I never
> > install the *-devel libs, and someone (probably you) always tells me to
> > install them, and then I am back in the race...
> >
> > Now, however, at make time:
> >
> > mv -f .libs/e-pilot-map.lo e-pilot-map.lo
> > make[3]: *** No rule to make target `e-pilot-util.c', needed by
> > `e-pilot-util.lo'.  Stop.
> > make[3]: Leaving directory
> > `/usr/src/redhat/SOURCES/evolution-0.10/e-util'
> > make[2]: *** [all-recursive] Error 1
> > make[2]: Leaving directory
> > `/usr/src/redhat/SOURCES/evolution-0.10/e-util'
> > make[1]: *** [all-recursive] Error 1
> > make[1]: Leaving directory `/usr/src/redhat/SOURCES/evolution-0.10'
> > make: *** [all-recursive-am] Error 2
> >
> >
> > On 05 Apr 2001 14:40:02 +0100, Ross Burton wrote:
> > > On 05 Apr 2001 14:52:54 +0200, Spacemonkey wrote:
> > > > Hi folks,
> > > >
> > > > I've been trying to compile evo with pilot support (sure wish it was in
> > > > the RPM, hint hint) with no luck.  When I run:
> > > >
> > > > ./configure --with-ldap=yes --enable-pilot-conduits=yes --with-pisock
> > > > --enable-pilotlinktest
> > > >
> > > > I get:
> > > >
> > > > checking for GAL >= 0.5.99.12... 0.5.99.13 found
> > > > checking for GtkHTML >= 0.8... 0.8.3 found
> > > > checking for GNOME-VFS >= 0.4.2... 1.0 found
> > > > checking for libxml >= 1.8.10... 1.8.10 found
> > > > checking for libunicode... configure: error: libunicode not found
> > > >
> > > > But I also have:
> > > >
> > > > libunicode-0.4.gnome-0_helix_1
> > >
> > > How about libunicode-devel?
> > >
> > > Ross
> > >
> > > -- 
> > > Ross Burton                     Software Engineer
> > > OneEighty Software Ltd          Tel: +44 20 8263 2332
> > > The Lansdowne Building          Fax: +44 20 8263 6314
> > > 2 Lansdowne Road                r burton 180sw com
> > > Croydon, Surrey CR9 2ER, UK     http://www.180sw.com./
> > > ====================================================================
> > > Under the Regulation of Investigatory Powers (RIP) Act 2000 together
> > > with any and all Regulations in force pursuant to the Act OneEighty
> > > Software Ltd reserves the right to monitor any or all incoming or
> > > outgoing communications as provided for under the Act
> >
> >
> > _______________________________________________
> > evolution maillist  -  evolution helixcode com
> > http://lists.helixcode.com/mailman/listinfo/evolution
>
>
> _______________________________________________
> evolution maillist  -  evolution helixcode com
> http://lists.helixcode.com/mailman/listinfo/evolution