Re: [Ekiga-list] Can't call landlines with other provider

[Reimundo Heluani <rheluani gmail com>]

On Fri, 2009-08-14 at 20:19 -0700, Reimundo Heluani wrote:
> On Thu, 2009-08-13 at 18:53 +0200, yannick wrote:
> > Reimundo Heluani a écrit :
> > > Hello List, I am new to SIP and I just built ekiga 3.2.5 from source on
> > > a LFS Linux 86x_64 2.6.29.5. I can run the echo test and it works fine,
> > > but if I try to use my voipdiscount.com account, about 10 seconds after
> > > dialing out it says "User not available" regardless of the phone dialed.
> > > 
> > > The problem is that I don't really know how to start debugging this, is
> > > there a debug mode for Ekiga?
> > > 
> > 
> > Yes, please provide us a debug output:
> > http://wiki.ekiga.org/index.php/Debugging_Ekiga#How_to_get_a_debug_output
> > 
> Allright, so I can see this line
> 
> "2009/08/13 12:28:54.066   0:10.376         CallSetup:0xf0358910 SIP
> PDU is likely too large (1615 bytes) for UDP datagram."
> 
> is this related to 
> 
> http://bugzilla.gnome.org/show_bug.cgi?id=341518
> 
> and if so, my MTU on my ethernet card can be to 4000 and it still fails.
> Also, the echo test still works and the log shows those lines anyways.
> Finally, running from another Linux and Ekiga 3.2.0 I can call with
> voipdiscount.com and the logs don't show those lines abot the PDU being
> too large.
> 
> R.

Ok, so deleting all codecs but gsm I can get the call finally, so I
guess it was #34518. I'll play a little with MTU vs. allowing some
codecs, could you guys tell me more or less what's a good combination? 

Thanks, 

R.
> 
> > > Another issues I have (that may be completely unrelated) are
> > > 
> > > 1) If I check on General Settings --> Disable Network detection, then
> > > the Ekiga.net account doesn't register (it says Globally not accepted) 
> > > 
> > 
> > That is not an issue, it only means your current setup prevent
> > end-to-end communication and you need a helper for that. Left it uncheck.
> > 
> > > 2) I have pulseaudio running on my system and I have to use the
> > > "Default" (PTLIB/ALSA) sink therefore, but my card (and webcam) are
> > > constantly bombarded. If I have pavucontrol open and test any sound from
> > > Ekiga, the cpu goes to 99% activity and I have to kill he stream.
> > > 
> > 
> > Does it work better without pulse audio? If so, please report a bug to
> > pulse audio.
> > 
> > > I know I'm not giving enough information but I don't really know where
> > > to begin, I you could point me in any direction to start debugging I'll
> > > be thankful. 
> > > 
> > > I just installed ptlib-2.6.4, opal-3.6.4 but no pwlib.
> > > 
> > > Cheers, 
> > > 
> > > R.
> > > 
> > > _______________________________________________
> > > ekiga-list mailing list
> > > ekiga-list gnome org
> > > http://mail.gnome.org/mailman/listinfo/ekiga-list
> > > 
> > > 
> > 
> > _______________________________________________
> > ekiga-list mailing list
> > ekiga-list gnome org
> > http://mail.gnome.org/mailman/listinfo/ekiga-list
>