Re: manage a modem connection




I went through the nm-connection-edit process and indeed, it works with "nmcli con up nameofconnection". This settles a IP address for the wwan
interface as expected and, mmcli shows a bearer.

Thank you very much for guiding me towards the solution

Best Regards

Edouard

On mar., mars 30 2021, edouard debry wrote:
Thanks for the piece of advice. I try that.

Regards


Le mar. 30 mars 2021 à 14:47, Aleksander Morgado <aleksander aleksander es>
a écrit :

Hey,

> >> I have a "e3372h-153" Huawei 4G USB dongle.
> >>
> >> This dongle works with the "huawei_cdc_ncm" kernel driver.
> >>
> >> Once connected,  two devices appear : /dev/ttyUSB0 and
> >> /dev/cdc-wdm1.
> >> These ones are used to talk to the modem itself.
> >>
> >> There is also a network interface appearing, which is (I
> >> believe)
> >> related to the driver "huawei_cdc_ncm" and the NCM > >> protocol :
> >>
> >> wwx001e101f0000: flags=4098<BROADCAST,MULTICAST>  mtu 1500
> >> ether 00:1e:10:1f:00:00 txqueuelen 1000 > >> (Ethernet)
> >>
> >> I am able to connect the modem with "mmcli ...", yet still > >> I
> >> have
> >> to configure
> >> the corresponding network interface in order to access the
> >> web.
> >
> > When using only ModemManager/mmcli this is expected, > > yes. You
> > need to
> > look for the connected bearer details (e.g. mmcli -b 0 > > probably)
> > and
> > then apply the IP addressing changes showed there.
> >
>
> I cannot find any bearer.
>

When using NetworkManager, you should get a bearer object once you're
connected.

> >> But this
> >> interface does not show up with "nmcli device show". I am
> >> however
> >> able to
> >> issue "dhclient wwx001e101f0000" and it works.
> >>
> >
> > NetworkManager does not refer to the modem based on the > > network
> > interface it exposes, it refers to the modem based on the
> > primary
> > control port exposed by the modem (e.g. cdc-wdm0 probably).
> >
>
> Ok, I understand, "nmcli -m 0" gives :
>
>   System   |               device:
>   /sys/devices/pci0000:00/0000:00:14.0/usb1/1-1/1-1.1/1-1.1.3
>            |              drivers: huawei_cdc_ncm, option1
>            |               plugin: huawei
>            |         primary port: ttyUSB0
> | ports: cdc-wdm1 (at), ttyUSB0 > (at),
>            wwx001e101f0000 (net)
>
> so, there are two control ports and one data > port. NetworkManager
> defaults to the primary port :
>
> ttyUSB0: déconnecté
>         "Intel Sunrise Point-LP 3.0 xHCI"
>         gsm (huawei_cdc_ncm, option1), hw
>

What ModemManager version are you using?
I think at some point the logic changed so that the cdc-wdm port is only set as primary port if there is no other port explicitly flagged as primary. That shouldn't be a problem to bring the connection up
with the net port, though (I think!)

>
> >> I also tried "nm-connection-editor". This one finds the > >> modem
> >> (gsm) but it seems to
> >> settle a connection through ppp.I would prefer a > >> connection
> >> through wwx001e101f0000
> >> because it uses the NCM protocol, known to be faster than > >> PPP.
> >>
> >
> > This is the way to go. If ModemManager doesn't use the > > cdc-wdm
> > port
> > plus the network interface for the connection, there must > > be a
> > reason
> > for that, we need to find why.
> >
> > Do the cdc-wdm and the net port show up in the list of > > ports
> > reported
> > in "mmcli -m 0"?
> >
>
> yes, but I tried again, nm-connection-editor lets me choose
> "Mobile Connection",
> but I see settings for PPP.
>

Oh, but you seeing settings for PPP doesn't mean the connection will be using PPP. If ModemManager decides at runtime that the connection
goes through the net port, the PPP settings will be ignored.

> >> Then, how come that I cannot see and configure > >> wwx001e101f0000
> >> with nmcli, just like
> >> any other network (wired, wifi) interface ?
> >
> > Because that interface is a modem network interface, and so > > the
> > main
> > interface that NetworkManager would refer to is the control
> > port, not
> > the data port (as the data port is chosen dynamically on
> > runtime).
>
> Ok, I understand.
>
> Maybe this is because NetworkManager sees ttyUSB0 first and > then
> thinks
> it is a PPP connection. How could I make NetworkManager > consider
> only
> cdc-wdm1 (in my c

As said before, NetworkManager is not thinking it will be a PPP
connection, NM cannot know in advance what kind of connection it will be. Well it could, but it doesn't really do any guess. Instead NM
waits for the bearer object exposed by MM to know which kind of
connection it will be.

Please try to connect the modem using NetworkManager, ignore the PPP settings in nm-connection-editor, and get the output of mmcli -b 0 to see what the bearer settings are (once connected!). If the settings in the bearer object say that PPP is requested over the ttyUSB, then please rerun everything while gathering MM+NM debug logs, to try to
see why exactly the net port was ignored:
https://www.freedesktop.org/wiki/Software/ModemManager/Debugging/


--
Aleksander
https://aleksander.es




[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]