|
That is
very helpful. I have been using WiFi analyzer on my Android
phone because I didn't know a good way to get the data on my
laptop. On 10/23/19 12:41 AM, Thomas Haller
wrote:
On Tue, 2019-10-22 at 15:02 -0700, Clive McCarthy via networkmanager- list wrote:You know, I wish that the Network Manager would report the signal strength in dBm instead of the silly sector icon. But that is for another day.nmcli -f SIGNAL,BSSID,SSID device wifi nmcli -f ALL device wifi best, ThomasOn 10/22/19 2:24 PM, Dan Williams wrote:On Tue, 2019-10-22 at 13:37 -0700, Clive McCarthy wrote:I rand the commands you suggested but the response doesn't look like a log dump. I guess they just enable logging. method return time=1571775394.161873 sender=:1.8 -> destination=:1.507 serial=32493 reply_serial=2 method return time=1571775429.864202 sender=:1.8 -> destination=:1.508 serial=32496 reply_serial=2 method return time=1571775528.578915 sender=:1.8 -> destination=:1.510 serial=32636 reply_serial=2 Can you point me to where the log files might be or at least their names.If your distribution uses systemd, they may be available with: journalctl -b -u wpa_supplicant if your distro does not uses systemd, then it'll be wherever syslog dumps that kind of output, like: /var/log/messages /var/log/wpa_supplicant.log /var/log/daemon.log DanOn 10/22/19 12:16 PM, Dan Williams wrote:On Tue, 2019-10-22 at 11:17 -0700, Clive McCarthy wrote:Thanks for your reply. My laptop, when first opened, reports (via the Network Manage, I suppose) that it is disconnected from the network. After a second or two it reports being connected. And it is. However, as I noted, the manager seems to choose the last known connection. This is a satisfactory algorithm for a fixed computer and for a computer connecting to a single AP. It isn't good for a movable computer with multiple APs. The Intel WiFi adapter is forced to shutdown when the computer is closed because there is a bug in the Intel-WiFi driver that doesn't handle suspend correctly. That is why there is a disconnect- connect sequence.In this case we'd need the wpa_supplicant logs described below to diagnose why the supplicant is picking that specific AP rather than another. DanOn 10/22/19 10:05 AM, Dan Williams wrote:On Mon, 2019-10-21 at 20:42 -0700, Clive McCarthy via networkmanager- list wrote:I have a situation where I have multiple APs in a building all with the same SSID and WPA key but set to non-clashing frequencies. When I close my laptop and WiFi shuts down and I move to a new location the Network Manager seems to connect to the original AP, rather than one with a much stronger signal. The algorithm for AP connection is suboptimal (in other words dumb). The selection process should scan ALL APs, figure out which ones are known (SSID and WPA); measure their signal strength and then choose the known AP with the strongest signal. How hard is that?This is what NetworkManager should already be doing. Two things to check: 1) NetworkManager depends on being notified by systemd or upower that the laptop has suspended so that it can reconfigure when it wakes up. It should be pretty clear if that's happening through the NetworkManager logs because it will say that it's going to sleep and waking up. For example: NetworkManager[1198]: <info> [1571720491.7590] manager: sleep: sleep requested (sleeping: no enabled: yes) NetworkManager[1198]: <info> [1571720491.7599] device (wlp61s0): state change: disconnected -> unmanaged (reason 'sleeping', sys- iface-state: 'managed') NetworkManager[1198]: <info> [1571720491.7615] manager: NetworkManager state is now ASLEEP NetworkManager[1198]: <warn> [1571752873.5481] sup- iface[0x55f38553aaa0,wlp61s0]: connection disconnected (reason -3) NetworkManager[1198]: <info> [1571752873.5504] device (wlp61s0): supplicant interface state: completed -> disconnected NetworkManager[1198]: <info> [1571752873.5803] manager: sleep: wake requested (sleeping: yes enabled: yes) NetworkManager[1198]: <info> [1571752873.6556] device (wlp61s0): state change: activated -> unmanaged (reason 'sleeping', sys- iface- state: 'managed') 2) enabling debug logging in wpa_supplicant with these two commands will show you exactly what's going on: sudo dbus-send --system --print-reply -- dest=fi.w1.wpa_supplicant1 /fi/w1/wpa_supplicant1 org.freedesktop.DBus.Properties.Set string:fi.w1.wpa_supplicant1 string:DebugTimestamp variant:boolean:true sudo dbus-send --system --print-reply -- dest=fi.w1.wpa_supplicant1 /fi/w1/wpa_supplicant1 org.freedesktop.DBus.Properties.Set string:fi.w1.wpa_supplicant1 string:DebugLevel variant:string:"msgdump" this will dump logs to wherever your system typically sends system logs, like the systemd journal or syslog. Once you have these logs, please review them to ensure there is no private information and then attach them to a reply so that we can figure out what's going on. Thanks! Dan_______________________________________________ networkmanager-list mailing list networkmanager-list gnome org https://mail.gnome.org/mailman/listinfo/networkmanager-list |