Re: A general (learning) query
- From: Ajay Garg <ajaygargnsit gmail com>
- To: "Andrew Bird (Sphere Systems)" <ajb spheresystems co uk>
- Cc: networkmanager-list gnome org
- Subject: Re: A general (learning) query
- Date: Mon, 18 Jun 2012 19:57:28 +0530
Thanks Andrew for the reply.
I ran "AT+CFUN=1".
Following are the outputs subsequently ::
########################################################################################################
Welcome to minicom 2.5
OPTIONS: I18n
Compiled on Feb 24 2011, 11:25:55.
Port /dev/ttyUSB0
Press CTRL-A Z for help on special keys
AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0
OK
AT+CFUN?
+CFUN: 1
OK
AT&V
&C: 1; &D: 2; &F: 0; E: 1; L: 1; M: 0; Q: 0; V: 1; X: 4; Z: 0; S0: 0;
S3: 13; S4: 10; S5: 8; S6: 2; S7: 45; S8: 2; S9: 6; S10: 14; S11: 95;
+FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 0; +DS: 0,0,2048,6;
+WS46: 12; +CBST: 0,0,1;
+CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
+CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0; +CGREG: 0;
+CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 0; +CGDCONT: (1,"IP","","0.0.0.0",0,0),(2,"IP","Ceibal","0.0.0.0",0,0),(3,"IP","gprs.ancel1","0.0.0.0",0,0),()
; +CGDSCONT: ; +CGTFT: ; +CGEQREQ: (1,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(2,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(3,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(4,2,0,0,0,0,2,0,"0E0",")
; +CGEQMIN: ; +CGQREQ: ; +CGQMIN: ; ; +CGEREP: 0,0; +CGCLASS: "A";
+CGSMS: 0; +CSMS: 0; +CMGF: 0; +CSCA: "",; +CSMP: ,,0,0; +CSDH: 0;
+CSCB: 0,"",""; +FDD: 0; +FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,;
+ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; ; +CPIN: ,; +CMEC: 0,0,0;
+CKPD: 1,1; +CGATT: 0; +CGACT: 0; +CPBS: "SM"; +CPMS: "SM","SM","SM";
+CNMI: 0,0,0,0,0; +CMMS: 2; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM: 96;
+FRM: 96; +CCUG: 0,0,0; +COPS: 0,2,""; +CUSD: 0; +CAOC: 1; +CCWA: 0;
+CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CLIP: 0;
+COLP: 0; +CLIR: 0; ^PORTSEL: 0; ^CPIN: ,; ^ATRECORD: 0;
^FREQLOCK: 10226476,12482272
OK
AT+CLAC
ERROR
AT+CPIN?
+CPIN: SIM PIN
OK
########################################################################################################
However, the same old problem, when running "sudo wvdial" ::::
########################################################################################################
-bash-4.1# sudo wvdial
--> WvDial: Internet dialer version 1.61
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Sending: AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
ERROR
--> Bad init string.
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Sending: AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
ERROR
--> Bad init string.
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2
ATQ0 V1 E1 S0=0 &C1 &D2
OK
--> Sending: AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
AT+CGDCONT=1,"IP","gprs.ancel","0.0.0.0",0,0
ERROR
--> Bad init string.
-bash-4.1#
########################################################################################################
One thing I noticed, that the last line of output of ATI for Dan's and my case, were different (Dan's output said "+GCAP: +CGSM,+FCLASS,+DS", while my output said "+GCAP: +CGSM,+DS,+ES").
Could that be an issue?
Regards,
Ajay
On Mon, Jun 18, 2012 at 7:42 PM, Andrew Bird (Sphere Systems)
<ajb spheresystems co uk> wrote:
On Monday 18 June 2012, Ajay Garg wrote:
> Sorry,
>
> forgot ATI.
>
>
>
> ###########################################################################
> ############################### Welcome to minicom 2.5
>
> OPTIONS: I18n
> Compiled on Feb 24 2011, 11:25:55.
> Port /dev/ttyUSB0
>
> Press CTRL-A Z for help on special
> keys
>
>
> AT S7=45 S0=0 L1 V1 X4 &c1 E1
> Q0
> OK
>
> AT&V
>
> &C: 1; &D: 2; &F: 0; E: 1; L: 1; M: 0; Q: 0; V: 1; X: 4; Z: 0; S0: 0;
> S3: 13; S4: 10; S5: 8; S6: 2; S7: 45; S8: 2; S9: 6; S10: 14; S11: 95;
> +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 0; +DS: 0,0,2048,6;
> +WS46: 12; +CBST: 0,0,1;
> +CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
> +CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0; +CGREG: 0;
> +CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 0; +CGDCONT:
> (1,"IP","","0.0.0.0",0,0),(2,"IP","Ceibal","0.0.0.0",0,0),(3,"IP","gprs.anc
> el1","0.0.0.0",0,0),() ; +CGDSCONT: ; +CGTFT: ; +CGEQREQ:
> (1,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(2,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(3,
> 2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(4,2,0,0,0,0,2,0,"0E0",") ; +CGEQMIN: ;
> +CGQREQ: ; +CGQMIN: ; ; +CGEREP: 0,0; +CGCLASS: "A"; +CGSMS: 0; +CSMS: 0;
> +CMGF: 0; +CSCA: "",; +CSMP: ,,0,0; +CSDH: 0; +CSCB: 0,"",""; +FDD: 0;
> +FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,;
> +ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; ; +CPIN: ,; +CMEC: 0,0,0;
> +CKPD: 1,1; +CGATT: 0; +CGACT: 0; +CPBS: "SM"; +CPMS: "SM","SM","SM";
> +CNMI: 0,0,0,0,0; +CMMS: 2; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM: 96;
> +FRM: 96; +CCUG: 0,0,0; +COPS: 0,2,""; +CUSD: 0; +CAOC: 1; +CCWA: 0;
> +CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CLIP: 0;
> +COLP: 0; +CLIR: 0; ^PORTSEL: 0; ^CPIN: ,; ^ATRECORD: 0;
> ^FREQLOCK: 10226476,12482272
>
> OK
> AT+CLAC
> ERROR
> AT+CPIN?
> +CPIN: SIM PIN
>
> OK
> ATI
> Manufacturer: huawei
> Model: E226
> Revision: 11.310.15.00.255
> IMEI: xxxxxxxxxxxxxxxx
> +GCAP: +CGSM,+DS,+ES
>
> OK
> ###########################################################################
> ###############################
>
>
>
>
> Thanks and Regards,
> Ajay
>
> On Mon, Jun 18, 2012 at 7:07 PM, Ajay Garg <
ajaygargnsit gmail com> wrote:
> > Hi Dan.
> >
> > Here is the output of "AT+CPIN?" (along with other commands, for brevity)
> >
> >
> >
> >
> >
> > ###########################################
> >
> > Welcome to minicom 2.5
> >
> > OPTIONS: I18n
> > Compiled on Feb 24 2011, 11:25:55.
> > Port /dev/ttyUSB0
> >
> > Press CTRL-A Z for help on special
> > keys
> >
> >
> > AT S7=45 S0=0 L1 V1 X4 &c1 E1
> > Q0
> > OK
> >
> > AT&V
> >
> > &C: 1; &D: 2; &F: 0; E: 1; L: 1; M: 0; Q: 0; V: 1; X: 4; Z: 0; S0: 0;
> > S3: 13; S4: 10; S5: 8; S6: 2; S7: 45; S8: 2; S9: 6; S10: 14; S11: 95;
> > +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 0; +DS: 0,0,2048,6;
> > +WS46: 12; +CBST: 0,0,1;
> > +CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
> > +CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0; +CGREG: 0;
> > +CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 0; +CGDCONT:
> > (1,"IP","","0.0.0.0",0,0),(2,"IP","Ceibal","0.0.0.0",0,0),(3,"IP","gprs.a
> > ncel1","0.0.0.0",0,0),() ; +CGDSCONT: ; +CGTFT: ; +CGEQREQ:
> > (1,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(2,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(
> > 3,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(4,2,0,0,0,0,2,0,"0E0",") ; +CGEQMIN:
> > ; +CGQREQ: ; +CGQMIN: ; ; +CGEREP: 0,0; +CGCLASS: "A"; +CGSMS: 0; +CSMS:
> > 0; +CMGF: 0; +CSCA: "",; +CSMP: ,,0,0; +CSDH: 0; +CSCB: 0,"",""; +FDD:
> > 0; +FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,;
> > +ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; ; +CPIN: ,; +CMEC: 0,0,0;
> > +CKPD: 1,1; +CGATT: 0; +CGACT: 0; +CPBS: "SM"; +CPMS: "SM","SM","SM";
> > +CNMI: 0,0,0,0,0; +CMMS: 2; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM: 96;
> > +FRM: 96; +CCUG: 0,0,0; +COPS: 0,2,""; +CUSD: 0; +CAOC: 1; +CCWA: 0;
> > +CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CLIP: 0;
> > +COLP: 0; +CLIR: 0; ^PORTSEL: 0; ^CPIN: ,; ^ATRECORD: 0;
> > ^FREQLOCK: 10226476,12482272
> >
> > OK
> > AT+CLAC
> > ERROR
> > AT+CPIN?
> > +CPIN: SIM PIN
> >
> > OK
> >
> > ###########################################
> >
> >
> >
> > Is it, in fact, an issue with the SIM?
> >
> >
> >
> > Regards,
> > Ajay
> >
> > On Fri, Jun 15, 2012 at 10:39 PM, Dan Williams <
dcbw redhat com> wrote:
> >> On Thu, 2012-06-14 at 08:07 -0400, Ajay Garg wrote:
> >> > Hi Dan.
> >>
> >> > The minicom output ::
> >> ########################################################################
> >> ##########################
> >>
> >> > AT&V
> >> > &C: 1; &D: 2; &F: 0; E: 1; L: 1; M: 0; Q: 0; V: 1; X: 4; Z: 0; S0: 0;
> >> > S3: 13; S4: 10; S5: 8; S6: 2; S7: 45; S8: 2; S9: 6; S10: 14; S11: 95;
> >> > +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 0; +DS:
> >> > 0,0,2048,6;
> >> > +WS46: 12; +CBST: 0,0,1;
> >> > +CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
> >> > +CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0; +CGREG: 0;
> >>
> >> > +CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 0; +CGDCONT:
> >> (1,"IP","","0.0.0.0",0,0),(2,"IP","Ceibal","0.0.0.0",0,0),(3,"IP","gprs.
> >> ancel1)
> >>
> >> > ; +CGDSCONT: ; +CGTFT: ; +CGEQREQ:
> >> (1,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(2,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),
> >> (3,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(4,2,0)
> >>
> >> > ; +CGEQMIN: ; +CGQREQ: ; +CGQMIN: ; ; +CGEREP: 0,0; +CGCLASS: "A";
> >> > +CGSMS: 0; +CSMS: 0; +CMGF: 0; +CSCA: "",; +CSMP: ,,0,0; +CSDH: 0;
> >> > +CSCB: 0,"",""; +FDD: 0; +FAR: 0; +FCL: 0; +FIT: 0,0; +ES: ,,;
> >> > +ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; ; +CPIN: ,; +CMEC: 0,0,0;
> >> > +CKPD: 1,1; +CGATT: 0; +CGACT: 0; +CPBS: "SM"; +CPMS: "SM","SM","SM";
> >> > +CNMI: 0,0,0,0,0; +CMMS: 2; +FTS: 0; +FRS: 0; +FTH: 3; +FRH: 3; +FTM:
> >> > 96;
> >> > +FRM: 96; +CCUG: 0,0,0; +COPS: 0,2,""; +CUSD: 0; +CAOC: 1; +CCWA: 0;
> >> > +CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0; +CLIP: 0;
> >> > +COLP: 0; +CLIR: 0; ^PORTSEL: 0; ^CPIN: ,; ^ATRECORD: 0;
> >> > ^FREQLOCK: 10226476,12482272
> >> >
> >> > OK
> >> > AT+CLAC
> >> > ERROR
> >> > AT+CPIN
> >> > ERROR
> >>
> >> You want "AT+CPIN?" here. Also, what does "ATI" say? For example, mine
> >> says:
> >>
> >> Manufacturer: huawei
> >> Model: E226
> >> Revision: 11.310.15.00.150
> >> IMEI: xxxxxxxxxxxxxx
> >> +GCAP: +CGSM,+FCLASS,+DS
> >>
> >> But I also get a response for AT+CLAC, so... The only thing I can think
> >> of is that the modem doesn't like your SIM. Any chance you can try
> >> another SIM?
> >>
> >> Dan
> >>
> >>
> >> ########################################################################
> >> ##########################
> >>
> >> > From the modem's labels ::
> >> ########################################################################
> >> ##########################
> >>
> >> > HUAWEI E226
> >> > PIN:8518
> >>
> >> ########################################################################
> >> ##########################
> >>
> >> > Regards,
> >> > Ajay
> >> >
> >> > On Wed, Jun 13, 2012 at 5:44 PM, Dan Williams <
dcbw redhat com> wrote:
> >> > On Wed, 2012-06-13 at 02:28 +0530, Ajay Garg wrote:
> >> > > Two things to check:
> >> > >
> >> > > 1) is the SIM correctly inserted?
> >> > >
> >> > > I guess yes, since we do get the output of AT&V.
> >> >
> >> > What does "AT+CPIN?" say?
> >> >
> >> > > Anyways, I rebooted. Same result as follows ::
> >> ########################################################################
> >> #############
> >>
> >> > > Welcome to minicom 2.5
> >> > >
> >> > > OPTIONS: I18n
> >> > > Compiled on Feb 24 2011, 11:25:55.
> >> > > Port /dev/ttyUSB0
> >> > >
> >> > > Press CTRL-A Z for help on special
> >> > > keys
> >> > >
> >> > > AT S7=45 S0=0 L1 V1 X4 &c1 E1
> >> > > Q0
> >> > > OK
> >> > > AT&V
> >> >
> >> > > &C: 1; &D: 2; &F: 0; E: 1; L: 1; M: 0; Q: 0; V: 1; X: 4; Z:
> >> > 0; S0: 0;
> >> >
> >> > > S3: 13; S4: 10; S5: 8; S6: 2; S7: 45; S8: 2; S9: 6; S10: 14;
> >> >
> >> > S11: 95;
> >> >
> >> > > +FCLASS: 0; +ICF: 3,3; +IFC: 2,2; +IPR: 115200; +DR: 0; +DS:
> >> > > 0,0,2048,6;
> >> > > +WS46: 12; +CBST: 0,0,1;
> >> > > +CRLP: (61,61,48,6,0),(61,61,48,6,1),(240,240,52,6,2);
> >> > > +CV120: 1,1,1,0,0,0; +CHSN: 0,0,0,0; +CSSN: 0,0; +CREG: 0;
> >> >
> >> > +CGREG: 0;
> >> >
> >> > > +CFUN:; +CSCS: "IRA"; +CSTA: 129; +CR: 0; +CRC: 0; +CMEE: 0;
> >> >
> >> > +CGDCONT:
> >> (1,"IP","","0.0.0.0",0,0),(2,"IP","Ceibal","0.0.0.0",0,0),(3,"IP","gprs.
> >> ancel1","0.0.0.0",0,0),()
> >>
> >> > > ; +CGDSCONT: ; +CGTFT: ; +CGEQREQ:
> >> (1,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(2,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),
> >> (3,2,0,0,0,0,2,0,"0E0","0E0",3,0,0),(4,2,0,0,0,0,2,0,"0E0",")
> >>
> >> > > ; +CGEQMIN: ; +CGQREQ: ; +CGQMIN: ; ; +CGEREP: 0,0;
> >> >
> >> > +CGCLASS: "A";
> >> >
> >> > > +CGSMS: 0; +CSMS: 0; +CMGF: 0; +CSCA: "",; +CSMP: ,,0,0;
> >> >
> >> > +CSDH: 0;
> >> >
> >> > > +CSCB: 0,"",""; +FDD: 0; +FAR: 0; +FCL: 0; +FIT: 0,0;
> >> >
> >> > +ES: ,,;
> >> >
> >> > > +ESA: 0,,,,0,0,255,; +CMOD: 0; +CVHU: 1; ; +CPIN: ,; +CMEC:
> >> > 0,0,0;
> >> >
> >> > > +CKPD: 1,1; +CGATT: 0; +CGACT: 0; +CPBS: "SM"; +CPMS:
> >> > "SM","SM","SM";
> >> >
> >> > > +CNMI: 0,0,0,0,0; +CMMS: 2; +FTS: 0; +FRS: 0; +FTH: 3; +FRH:
> >> > 3; +FTM:
> >> > > 96;
> >> > > +FRM: 96; +CCUG: 0,0,0; +COPS: 0,2,""; +CUSD: 0; +CAOC: 1;
> >> >
> >> > +CCWA: 0;
> >> >
> >> > > +CLVL: 2; +CMUT: 0; +CPOL: 0,2,"",0,0,0; +CPLS: 0; +CTZR: 0;
> >> >
> >> > +CLIP: 0;
> >> >
> >> > > +COLP: 0; +CLIR: 0; ^PORTSEL: 0; ^CPIN: ,; ^ATRECORD: 0;
> >> > > ^FREQLOCK: 10226476,12482272
> >> > >
> >> > > OK
> >> > > AT+CLAC
> >> > > ERROR
> >> > > AT+CGDCONT=?
> >> > > ERROR
> >>
> >> ########################################################################
> >> #############
> >>
> >> > > 2) Is this really a GSM/UMTS modem? What's the
> >> >
> >> > brand and
> >> >
> >> > > model number?
> >> > >
> >> > > Again, I guess yes.
> >> >
> >> > Unfortunately lsusb doesn't give us the actual model number,
> >> > since
> >> > Huawei uses the same USB IDs for multiple devices. What's the
> >> > actual
> >> > model number from the sticker on the modem itself?
> >> >
> >> > Dan
> >>
> >> ########################################################################
> >> #############
> >>
> >> > > -bash-4.1# lsusb
> >> > >
> >> > > Bus 002 Device 002: ID 12d1:1003 Huawei Technologies Co.,
> >> >
> >> > Ltd. E220
> >> >
> >> > > HSDPA Modem / E230/E270 HSDPA/HSUPA Modem
> >> > > Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root
> >> >
> >> > hub
> >> >
> >> > > Bus 001 Device 002: ID 1286:2001 Marvell Semiconductor, Inc.
> >> >
> >> > 88W8388
> >> >
> >> > > 802.11a/b/g WLAN
> >> > > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root
> >> >
> >> > hub
> >>
> >> ########################################################################
> >> #############
> >>
> >> > > Regards,
> >> > > Ajay
> >> > >
> >> > > Dan
In the AT&V the +CFUN value looks odd to me.
What does AT+CFUN? show?
If you do AT+CFUN=1 do things improve?
Hope it helps
Andrew
[
Date Prev][
Date Next] [
Thread Prev][
Thread Next]
[
Thread Index]
[
Date Index]
[
Author Index]
