NM 0.7 svn on Gentoo
- From: Rod Keenan <keenan_rod yahoo com>
- To: networkmanager-list gnome org
- Subject: NM 0.7 svn on Gentoo
- Date: Thu, 12 Jun 2008 01:46:56 -0700 (PDT)
I'm attempting to get NM 0.7 working on an older Dell
laptop. I've
successfully installed an earlier version of NM before
on a different
laptop, but this is my first attempt at this version
with this kernel.
On eth0 it seems that dhcp isn't working since ping
returns unknown host
and /etc/resolv.conf isn't getting populated. (Or
isn't that used
anymore?) The hardware seems to be probed and
configured correctly with
the right drivers and firmware but the knetworkmanager
applet shows: No
network device found.
Wireless just seems to continuously scan.
Being new to 0.7 I'm not sure where to start looking
for the problem(s).
Below is a description of the environment and the
relevant log messages.
Hardware:
Dell Inspiron 5100
BCM4306 802.11b/g Wireless LAN Controller (rev 02)
BCM4401 100Base-T
Software:
linux-2.6.25-gentoo-r4
CONFIG_CFG80211=m
CONFIG_WIRELESS_EXT=y
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_DEFAULT_PID=y
CONFIG_MAC80211_RC_DEFAULT="pid"
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_LEDS=y
CONFIG_MAC80211_DEBUG=y
CONFIG_MAC80211_VERBOSE_DEBUG=y
CONFIG_TKIP_DEBUG=y
CONFIG_MAC80211_DEBUG_COUNTERS=y
CONFIG_MAC80211_VERBOSE_PS_DEBUG=y
CONFIG_RFKILL=m
CONFIG_RFKILL_INPUT=m
CONFIG_RFKILL_LEDS=y
CONFIG_B44=m
CONFIG_B44_PCI_AUTOSELECT=y
CONFIG_B44_PCICORE_AUTOSELECT=y
CONFIG_B44_PCI=y
CONFIG_B43=m
CONFIG_B43_PCI_AUTOSELECT=y
CONFIG_B43_PCICORE_AUTOSELECT=y
CONFIG_B43_LEDS=y
CONFIG_B43_RFKILL=y
CONFIG_B43_DEBUG=y
CONFIG_B43LEGACY=m
CONFIG_B43LEGACY_PCI_AUTOSELECT=y
CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
CONFIG_B43LEGACY_LEDS=y
CONFIG_B43LEGACY_RFKILL=y
CONFIG_B43LEGACY_DEBUG=y
CONFIG_B43LEGACY_DMA=y
CONFIG_B43LEGACY_PIO=y
CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
KDE 3.5
kde-misc/knetworkmanager
tried both: 0.2.1_pre20071119 and 0.2.1_p20071228
NM - SVN revision 3750
gnome-common - SVN revision 3913
sys-apps/hal-0.5.11-r1
app-misc/hal-info-20080310
dev-libs/glib-2.14.6
dev-libs/libgcrypt-1.4.0-r1
dev-libs/libgpg-error-1.6
dev-libs/libnl-1.1-r1
net-misc/dhcdbd-3.0
net-wireless/wireless-tools-29
net-wireless/wpa_supplicant-0.5.10
sys-apps/dbus-1.1.20
sys-apps/iproute2-2.6.22.20070710
sys-auth/policykit-0.7
Firmware:
broadcom-wl-4.150.10.5
wl_apsta-3.130.20.0.o
net-wireless/b43-fwcutter-011
With both versions of kde-misc/knetworkmanager the
following message
appears in .xsession-errors:
Could not open library knetworkmanager.la:
/usr/kde/3.5/lib/libkdeinit_knetworkmanager.so:
undefined symbol: ieee_802_11_cipher_validate
That probably explains why the applet shows: No
network device found. I
haven't figured out what the fix is yet though.
lsmod shows:
rfkill_input 4352 0
ipv6 202564 8
...
sbs 11912 0
sbshc 5632 1 sbs
...
b43legacy 107932 0
rfkill 6036 3 rfkill_input,b43legacy
mac80211 115724 1 b43legacy
cfg80211 7048 1 mac80211
input_polldev 4104 1 b43legacy
led_class 4228 1 b43legacy
...
b44 21264 0
...
ieee1394 68360 1 ohci1394
...
ssb 26372 2 b43legacy,b44
lspci shows:
02:01.0 Ethernet controller: Broadcom Corporation
BCM4401 100Base-T (rev 01)
02:02.0 Network controller: Broadcom Corporation
BCM4306 802.11b/g
Wireless LAN Controller (rev 02)
lshal shows:
...
udi =
'/org/freedesktop/Hal/devices/computer_logicaldev_input_5'
button.has_state = false (bool)
info.addons.singleton = {'hald-addon-input'}
(string list)
info.capabilities = {'input', 'button'} (string
list)
info.category = 'input' (string)
info.parent =
'/org/freedesktop/Hal/devices/computer' (string)
info.product = 'b43legacy-phy0' (string)
info.subsystem = 'input' (string)
info.udi =
'/org/freedesktop/Hal/devices/computer_logicaldev_input_5'
(string)
input.device = '/dev/input/event10' (string)
input.product = 'b43legacy-phy0' (string)
linux.device_file = '/dev/input/event10' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'input' (string)
linux.sysfs_path =
'/sys/devices/virtual/input/input10/event10' (string)
...
udi = '/org/freedesktop/Hal/devices/pci_14e4_4320'
info.linux.driver = 'b43-pci-bridge' (string)
info.parent =
'/org/freedesktop/Hal/devices/pci_8086_244e' (string)
info.product = 'BCM4306 802.11b/g Wireless LAN
Controller' (string)
info.subsystem = 'pci' (string)
info.udi =
'/org/freedesktop/Hal/devices/pci_14e4_4320' (string)
info.vendor = 'Broadcom Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:02.0'
(string)
pci.device_class = 2 (0x2) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 128 (0x80) (int)
pci.linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:02.0'
(string)
pci.product = 'BCM4306 802.11b/g Wireless LAN
Controller' (string)
pci.product_id = 17184 (0x4320) (int)
pci.subsys_product = 'TrueMobile 1300 WLAN Mini-PCI
Card' (string)
pci.subsys_product_id = 1 (0x1) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Broadcom Corporation' (string)
pci.vendor_id = 5348 (0x14e4) (int)
udi =
'/org/freedesktop/Hal/devices/net_00_90_4b_2f_a7_08_0'
info.capabilities = {'net', 'net.80211control'}
(string list)
info.category = 'net.80211control' (string)
info.parent =
'/org/freedesktop/Hal/devices/pci_14e4_4320' (string)
info.product = 'Networking Wireless Control
Interface' (string)
info.subsystem = 'net' (string)
info.udi =
'/org/freedesktop/Hal/devices/net_00_90_4b_2f_a7_08_0'
(string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:02.0/ssb0:0/net/wmaster0'
(string)
net.address = '00:90:4b:2f:a7:08' (string)
net.arp_proto_hw_id = 801 (0x321) (int)
net.interface = 'wmaster0' (string)
net.linux.ifindex = 3 (0x3) (int)
net.originating_device =
'/org/freedesktop/Hal/devices/pci_14e4_4320'
(string)
udi =
'/org/freedesktop/Hal/devices/net_00_90_4b_2f_a7_08'
info.capabilities = {'net', 'net.80211'} (string
list)
info.category = 'net.80211' (string)
info.parent =
'/org/freedesktop/Hal/devices/pci_14e4_4320' (string)
info.product = 'WLAN Interface' (string)
info.subsystem = 'net' (string)
info.udi =
'/org/freedesktop/Hal/devices/net_00_90_4b_2f_a7_08'
(string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:02.0/ssb0:0/net/wlan0'
(string)
net.80211.mac_address = 619736704776
(0x904b2fa708) (uint64)
net.address = '00:90:4b:2f:a7:08' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'wlan0' (string)
net.linux.ifindex = 4 (0x4) (int)
net.originating_device =
'/org/freedesktop/Hal/devices/pci_14e4_4320'
(string)
udi = '/org/freedesktop/Hal/devices/pci_14e4_4401'
info.linux.driver = 'b44' (string)
info.parent =
'/org/freedesktop/Hal/devices/pci_8086_244e' (string)
info.product = 'BCM4401 100Base-T' (string)
info.subsystem = 'pci' (string)
info.udi =
'/org/freedesktop/Hal/devices/pci_14e4_4401' (string)
info.vendor = 'Broadcom Corporation' (string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'pci' (string)
linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:01.0'
(string)
pci.device_class = 2 (0x2) (int)
pci.device_protocol = 0 (0x0) (int)
pci.device_subclass = 0 (0x0) (int)
pci.linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:01.0'
(string)
pci.product = 'BCM4401 100Base-T' (string)
pci.product_id = 17409 (0x4401) (int)
pci.subsys_product_id = 329 (0x149) (int)
pci.subsys_vendor = 'Dell' (string)
pci.subsys_vendor_id = 4136 (0x1028) (int)
pci.vendor = 'Broadcom Corporation' (string)
pci.vendor_id = 5348 (0x14e4) (int)
udi =
'/org/freedesktop/Hal/devices/net_00_0d_56_34_04_5e'
info.capabilities = {'net', 'net.80203',
'wake_on_lan'} (string list)
info.category = 'net.80203' (string)
info.interfaces =
{'org.freedesktop.Hal.Device.WakeOnLan'} (string list)
info.parent =
'/org/freedesktop/Hal/devices/pci_14e4_4401' (string)
info.product = 'Networking Interface' (string)
info.subsystem = 'net' (string)
info.udi =
'/org/freedesktop/Hal/devices/net_00_0d_56_34_04_5e'
(string)
linux.hotplug_type = 2 (0x2) (int)
linux.subsystem = 'net' (string)
linux.sysfs_path =
'/sys/devices/pci0000:00/0000:00:1e.0/0000:02:01.0/ssb1:0/net/eth0'
(string)
net.80203.mac_address = 57280824414 (0xd5634045e)
(uint64)
net.address = '00:0d:56:34:04:5e' (string)
net.arp_proto_hw_id = 1 (0x1) (int)
net.interface = 'eth0' (string)
net.linux.ifindex = 2 (0x2) (int)
net.originating_device =
'/org/freedesktop/Hal/devices/pci_14e4_4401'
(string)
org.freedesktop.Hal.Device.WakeOnLan.method_argnames =
{'', '',
'enable'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_execpaths
=
{'hal-system-wol-supported', 'hal-system-wol-enabled',
'hal-system-wol-enable'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_names =
{'GetSupported',
'GetEnabled', 'SetEnabled'} (string list)
org.freedesktop.Hal.Device.WakeOnLan.method_signatures
= {'', '',
'b'} (string list)
lshw shows:
*-network:0
description: Ethernet interface
product: BCM4401 100Base-T
vendor: Broadcom Corporation
physical id: 1
bus info: pci 0000:02:01.0
logical name: eth0
version: 01
serial: 00:0d:56:34:04:5e
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet
physical mii 10bt
10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on
broadcast=yes driver=b44
driverversion=2.0 duplex=full latency=32 link=yes
module=ssb
multicast=yes port=twisted pair speed=100MB/s
*-network:1
description: Network controller
product: BCM4306 802.11b/g Wireless LAN
Controller
vendor: Broadcom Corporation
physical id: 2
bus info: pci 0000:02:02.0
version: 02
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list
configuration: driver=b43-pci-bridge
latency=32 module=ssb
/var/log/messages shows:
Linux version 2.6.25-gentoo-r4 (root tux) (gcc version
4.2.4 (Gentoo
4.2.4 p1.0)) #65 SMP PREEMPT Thu Jun 12 02:18:14 UTC
2008
...
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2,
16384 bytes)
TCP established hash table entries: 16384 (order: 5,
131072 bytes)
TCP bind hash table entries: 16384 (order: 5, 131072
bytes)
TCP: Hash tables configured (established 16384 bind
16384)
TCP reno registered
...
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
...
ssb: Sonics Silicon Backplane found on PCI device
0000:02:02.0
...
ssb: Sonics Silicon Backplane found on PCI device
0000:02:01.0
...
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet
00:0d:56:34:04:5e
b43legacy-phy0: Broadcom 4306 WLAN found
b43legacy-phy0 debug: Found PHY: Analog 1, Type 2,
Revision 1
b43legacy-phy0 debug: Found Radio: Manuf 0x17F,
Version 0x2050, Revision 2
b43legacy-phy0 debug: Radio initialized
phy0: Selected rate control algorithm 'pid'
Broadcom 43xx-legacy driver loaded [ Features: PLRID,
Firmware-ID: FW10 ]
ieee1394: Host added: ID:BUS[0-00:1023]
GUID[474fc0000a16b861]
...
hald[3072]: error in fdi file
/etc/hal/fdi/policy/10-x11-input.fdi:1: no
element found
NetworkManager: <info> starting...
...
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
...
NetworkManager: <info> eth0: Device is
fully-supported using driver 'b44'.
NetworkManager: <info> Found new Ethernet device
'eth0'.
NetworkManager: <info> (eth0): exported as
/org/freedesktop/Hal/devices/net_00_0d_56_34_04_5e
NetworkManager: <info> wlan0: Device is
fully-supported using driver
'b43-pci-bridge'.
NetworkManager: <info> wlan0: driver supports SSID
scans (scan_capa 0x01).
NetworkManager: <info> Found new wireless (802.11)
device 'wlan0'.
NetworkManager: <info> (wlan0): exported as
/org/freedesktop/Hal/devices/net_00_90_4b_2f_a7_08
NetworkManager: <info> Trying to start the
supplicant...
NetworkManager: <info> Trying to start the system
settings daemon...
...
ADDRCONF(NETDEV_UP): eth0: link is not ready
NetworkManager: <info> (eth0): device state change: 1
-> 2
NetworkManager: <info> (eth0): bringing up device.
NetworkManager: <info> (eth0): preparing device.
NetworkManager: <info> (eth0): deactivating device.
NetworkManager: <info> (wlan0): device state change:
1 -> 2
NetworkManager: <info> (wlan0): bringing up device.
input: b43legacy-phy0 as
/devices/virtual/input/input10
b43legacy-phy0: Loading firmware version 0x127, patch
level 14
(2005-04-18 02:36:27)
b43legacy-phy0 debug: Chip initialized
b43legacy-phy0 debug: 30-bit DMA initialized
Registered led device: b43legacy-phy0:tx
Registered led device: b43legacy-phy0:rx
Registered led device: b43legacy-phy0:radio
b43legacy-phy0 debug: Wireless interface started
b43legacy-phy0 debug: Adding Interface type 2
HW CONFIG: channel=1 freq=2412 phymode=2
ADDRCONF(NETDEV_UP): wlan0: link is not ready
NetworkManager: <info> (wlan0): preparing device.
NetworkManager: <info> (wlan0): deactivating device.
NetworkManager: <info> (wlan0): device state change:
2 -> 3
HW CONFIG: channel=1 freq=2412 phymode=2
HW CONFIG: channel=2 freq=2417 phymode=2
HW CONFIG: channel=3 freq=2422 phymode=2
HW CONFIG: channel=4 freq=2427 phymode=2
HW CONFIG: channel=5 freq=2432 phymode=2
NetworkManager: <info> (wlan0): supplicant interface
state change: 1 -> 2.
HW CONFIG: channel=6 freq=2437 phymode=2
HW CONFIG: channel=7 freq=2442 phymode=2
HW CONFIG: channel=8 freq=2447 phymode=2
HW CONFIG: channel=9 freq=2452 phymode=2
HW CONFIG: channel=10 freq=2457 phymode=2
HW CONFIG: channel=11 freq=2462 phymode=2
HW CONFIG: channel=1 freq=2412 phymode=2
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
NetworkManager: <info> (eth0): carrier now ON (device
state 2)
NetworkManager: <info> (eth0): device state change: 2
-> 3
eth0: no IPv6 routers present
HW CONFIG: channel=1 freq=2412 phymode=2
HW CONFIG: channel=2 freq=2417 phymode=2
HW CONFIG: channel=3 freq=2422 phymode=2
HW CONFIG: channel=4 freq=2427 phymode=2
HW CONFIG: channel=5 freq=2432 phymode=2
HW CONFIG: channel=6 freq=2437 phymode=2
HW CONFIG: channel=7 freq=2442 phymode=2
HW CONFIG: channel=8 freq=2447 phymode=2
HW CONFIG: channel=9 freq=2452 phymode=2
HW CONFIG: channel=10 freq=2457 phymode=2
HW CONFIG: channel=11 freq=2462 phymode=2
HW CONFIG: channel=1 freq=2412 phymode=2
...
ifconfig shows:
eth0 Link encap:Ethernet HWaddr
00:0D:56:34:04:5E
inet6 addr: fe80::20d:56ff:fe34:45e/64
Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:11 errors:0 dropped:0 overruns:0
frame:0
TX packets:6 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:1000
RX bytes:3985 (3.8 Kb) TX bytes:492 (492.0
b)
Interrupt:7
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wlan0 Link encap:Ethernet HWaddr
00:90:4B:2F:A7:08
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wmaster0 Link encap:UNSPEC HWaddr
00-90-4B-2F-A7-08-38-60-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING MULTICAST MTU:1500
Metric:1
RX packets:0 errors:0 dropped:0 overruns:0
frame:0
TX packets:0 errors:0 dropped:0 overruns:0
carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
iwconfig shows:
lo no wireless extensions.
eth0 no wireless extensions.
wmaster0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:""
Mode:Managed Frequency:2.412 GHz Access
Point: Not-Associated
Tx-Power=27 dBm
Retry min limit:7 RTS thr:off Fragment
thr=2352 B
Encryption key:off
Link Quality:0 Signal level:0 Noise
level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx
invalid frag:0
Tx excessive retries:0 Invalid misc:0
Missed beacon:0
I hope this gives enough info to pinpoint the
problems.
Thanks,
Rod
[
Date Prev][
Date Next] [
Thread Prev][
Thread Next]
[
Thread Index]
[
Date Index]
[
Author Index]
