Re: Corporate Networks & Hidden SSID
- From: Dan Williams <dcbw redhat com>
- To: Grant Williamson <traxtopel gmail com>
- Cc: networkmanager-list gnome org
- Subject: Re: Corporate Networks & Hidden SSID
- Date: Thu, 25 Jan 2007 07:58:22 -0500
On Thu, 2007-01-25 at 10:51 +0100, Grant Williamson wrote:
> Dan,
> here is another example, SSID Broadcast disabled on a home network.
> Using wpa_supplicant alone I can connect(less than 5 seconds).
> Using network manager I cannot. Note in both examples I have preset the
> SSID.
> I am using NetworkManager 0.6.4 and have tried wpa_supplicant 0.4.8 & 0.5.7
>
> ############################################################################
> cat wpa_supplicant.conf
> ctrl_interface=/var/run/wpa_supplicant
Can you try adding "ap_scan=2" here and retry the connect? NM is using
that likely because it's a hidden network, lets try to narrow down what
the problem is. Let us know the results.
Thanks,
Dan
> network={
> ssid="ATMEL"
> scan_ssid=1
> proto=WPA
> key_mgmt=WPA-PSK
> pairwise=CCMP TKIP
> group=CCMP TKIP WEP104 WEP40
> psk=<removed>
> }
> ############################################################################
> WPA_SUPPLICANT
>
> [root lc4eb7681638218 eap]# iwconfig eth1 essid ATMEL
>
> [root lc4eb7681638218 eap]# iwconfig
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> eth1 unassociated ESSID:"ATMEL" Nickname:"ipw2100"
> Mode:Managed Channel=0 Access Point: Not-Associated
> Bit Rate=0 kb/s Tx-Power:16 dBm
> Retry min limit:7 RTS thr:off Fragment thr:off
> Encryption key:off
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:5 Missed beacon:0
>
> sit0 no wireless extensions.
>
>
> [root test eap]# wpa_supplicant -Dwext -w -cwpa_supplicant.conf -ieth1 -dd
> Initializing interface 'eth1' conf 'wpa_supplicant.conf' driver 'wext'
> ctrl_interface 'N/A' bridge 'N/A'
> Configuration file 'wpa_supplicant.conf' -> '/etc/eap/wpa_supplicant.conf'
> Reading configuration file '/etc/eap/wpa_supplicant.conf'
> ctrl_interface='/var/run/wpa_supplicant'
> Line: 2 - start of a new network block
> ssid - hexdump_ascii(len=5):
> 41 54 4d 45 4c ATMEL
> scan_ssid=1 (0x1)
> proto: 0x1
> key_mgmt: 0x2
> pairwise: 0x18
> group: 0x1e
> PSK - hexdump(len=32): [REMOVED]
> Priority group 0
> id=0 ssid='ATMEL'
> Initializing interface (2) 'eth1'
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> EAPOL: SUPP_BE entering state INITIALIZE
> EAP: EAP entering state DISABLED
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> SIOCGIWRANGE: WE(compiled)=20 WE(source)=18 enc_capa=0xf
> capabilities: key_mgmt 0xf enc 0xf
> WEXT: Operstate: linkmode=1, operstate=5
> Own MAC address: 00:0c:f1:1e:89:0b
> wpa_driver_wext_set_wpa
> wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_countermeasures
> wpa_driver_wext_set_drop_unencrypted
> Setting scan request: 0 sec 100000 usec
> Added interface eth1
> RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> Wireless event: cmd=0x8b06 len=8
> State: DISCONNECTED -> SCANNING
> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=5):
> 41 54 4d 45 4c ATMEL
> Trying to get current scan results first without requesting a new scan
> to speed up initial association
> Received 1521 bytes of scan results (6 BSSes)
> Scan results: 6
> Selecting BSS from priority group 0
> 0: 00:13:10:68:4f:1c ssid='ATMEL' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
> selected based on WPA IE
> Trying to associate with 00:13:10:68:4f:1c (SSID='ATMEL' freq=2432 MHz)
> Cancelling scan request
> WPA: clearing own WPA/RSN IE
> Automatic auth_alg selection: 0x1
> WPA: using IEEE 802.11i/D3.0
> WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2 proto 1
> WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2
> 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> WPA: clearing AP RSN IE
> WPA: using GTK TKIP
> WPA: using PTK TKIP
> WPA: using KEY_MGMT WPA-PSK
> WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00
> 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> No keys have been configured - skip key clearing
> wpa_driver_wext_set_drop_unencrypted
> State: SCANNING -> ASSOCIATING
> wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> WEXT: Operstate: linkmode=-1, operstate=5
> wpa_driver_wext_associate
> ioctl[SIOCSIWFREQ]: Operation not supported
> Association request to the driver failed
> Setting authentication timeout: 5 sec 0 usec
> EAPOL: External notification - EAP success=0
> EAPOL: External notification - EAP fail=0
> EAPOL: External notification - portControl=Auto
> RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> Wireless event: cmd=0x8b06 len=8
> RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> Wireless event: cmd=0x8b1a len=14
> RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
> Wireless event: cmd=0x8b15 len=20
> Wireless event: new AP: 00:13:10:68:4f:1c
> State: ASSOCIATING -> ASSOCIATED
> wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> WEXT: Operstate: linkmode=-1, operstate=5
> Associated to a new BSS: BSSID=00:13:10:68:4f:1c
> No keys have been configured - skip key clearing
> Associated with 00:13:10:68:4f:1c
> WPA: Association event - clear replay counter
> EAPOL: External notification - portEnabled=0
> EAPOL: External notification - portValid=0
> EAPOL: External notification - EAP success=0
> EAPOL: External notification - portEnabled=1
> EAPOL: SUPP_PAE entering state CONNECTING
> EAPOL: SUPP_BE entering state IDLE
> Setting authentication timeout: 10 sec 0 usec
> Cancelling scan request
> RTM_NEWLINK: operstate=0 ifi_flags=0x11003 ([UP][LOWER_UP])
> RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX EAPOL from 00:13:10:68:4f:1c
> RX EAPOL - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00 00 00 00
> 00 02 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce e5 98 05 0b
> 53 f0 ee ae 8b 2a 5e d4 f4 31 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00
> Setting authentication timeout: 10 sec 0 usec
> IEEE 802.1X RX: version=1 type=3 length=95
> EAPOL-Key type=254
> key_info 0x89 (ver=1 keyidx=0 rsvd=0 Pairwise Ack)
> key_length=32 key_data_length=0
> replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 02
> key_nonce - hexdump(len=32): b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20
> 09 21 81 ce e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 31
> key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_mic - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> WPA: RX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 00 89 00 20 00 00 00
> 00 00 00 00 02 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce e5
> 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 31 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> State: ASSOCIATED -> 4WAY_HANDSHAKE
> WPA: RX message 1 of 4-Way Handshake from 00:13:10:68:4f:1c (ver=1)
> WPA: Renewed SNonce - hexdump(len=32): fc 26 2c a1 e2 16 e1 1b 2d 47 d6
> 67 09 c4 60 45 46 93 5e 9f 3b 1d 26 01 b9 16 d8 40 f7 1a 20 2e
> WPA: PMK - hexdump(len=32): [REMOVED]
> WPA: PTK - hexdump(len=64): [REMOVED]
> WPA: WPA IE for msg 2/4 - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50
> f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> WPA: Sending EAPOL-Key 2/4
> WPA: TX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 09 00 20 00 00
> 00 00 00 00 00 02 fc 26 2c a1 e2 16 e1 1b 2d 47 d6 67 09 c4 60 45 46 93
> 5e 9f 3b 1d 26 01 b9 16 d8 40 f7 1a 20 2e 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0 18
> 9e e9 b4 f5 f7 ea 7c 8f 72 01 f2 3c 02 d9 00 18 dd 16 00 50 f2 01 01 00
> 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> RX EAPOL from 00:13:10:68:4f:1c
> RX EAPOL - hexdump(len=123): 01 03 00 77 fe 01 c9 00 20 00 00 00 00 00
> 00 00 03 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce e5 98 05
> 0b 53 f0 ee ae 8b 2a 5e d4 f4 31 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9f 70 ed 56 bb
> b6 2f 11 81 4c 4a 77 8f a4 5a ec 00 18 dd 16 00 50 f2 01 01 00 00 50 f2
> 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> IEEE 802.1X RX: version=1 type=3 length=119
> EAPOL-Key type=254
> key_info 0x1c9 (ver=1 keyidx=0 rsvd=0 Pairwise Install Ack MIC)
> key_length=32 key_data_length=24
> replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 03
> key_nonce - hexdump(len=32): b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20
> 09 21 81 ce e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 31
> key_iv - hexdump(len=16): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_mic - hexdump(len=16): 9f 70 ed 56 bb b6 2f 11 81 4c 4a 77 8f a4 5a ec
> WPA: RX EAPOL-Key - hexdump(len=123): 01 03 00 77 fe 01 c9 00 20 00 00
> 00 00 00 00 00 03 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce
> e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 31 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 9f 70
> ed 56 bb b6 2f 11 81 4c 4a 77 8f a4 5a ec 00 18 dd 16 00 50 f2 01 01 00
> 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
> State: 4WAY_HANDSHAKE -> 4WAY_HANDSHAKE
> WPA: RX message 3 of 4-Way Handshake from 00:13:10:68:4f:1c (ver=1)
> WPA: IE KeyData - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02
> 01 00 00 50 f2 02 01 00 00 50 f2 02
> WPA: Sending EAPOL-Key 4/4
> WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 01 09 00 20 00 00 00
> 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 53 8d 77
> ab ae 54 52 6f e5 d7 b7 b2 bb 37 b8 e9 00 00
> WPA: Installing PTK to the driver.
> WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
> wpa_driver_wext_set_key: alg=2 key_idx=0 set_tx=1 seq_len=6 key_len=32
> State: 4WAY_HANDSHAKE -> GROUP_HANDSHAKE
> EAPOL: startWhen --> 0
> EAPOL: SUPP_PAE entering state CONNECTING
> EAPOL: txStart
> WPA: drop TX EAPOL in non-IEEE 802.1X mode (type=1 len=0)
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX EAPOL from 00:13:10:68:4f:1c
> RX EAPOL - hexdump(len=131): 01 03 00 7f fe 03 a1 00 20 00 00 00 00 00
> 00 00 05 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce e5 98 05
> 0b 53 f0 ee ae 8b 2a 5e d4 f4 2f 81 ce e5 98 05 0b 53 f0 ee ae 8b 2a 5e
> d4 f4 32 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c3 ae e1 31 81
> da 33 ec 5a 13 93 df 03 c1 f5 75 00 20 41 95 1f 51 7a 69 e2 a3 65 2c 46
> 30 c0 7d fe 4a 1a 22 5b dc fb ad 37 c7 3b c9 9d 99 ca 62 7d 41
> IEEE 802.1X RX: version=1 type=3 length=127
> EAPOL-Key type=254
> key_info 0x3a1 (ver=1 keyidx=2 rsvd=0 Group Ack MIC Secure)
> key_length=32 key_data_length=32
> replay_counter - hexdump(len=8): 00 00 00 00 00 00 00 05
> key_nonce - hexdump(len=32): b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20
> 09 21 81 ce e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 2f
> key_iv - hexdump(len=16): 81 ce e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 32
> key_rsc - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_id (reserved) - hexdump(len=8): 00 00 00 00 00 00 00 00
> key_mic - hexdump(len=16): c3 ae e1 31 81 da 33 ec 5a 13 93 df 03 c1 f5 75
> WPA: RX EAPOL-Key - hexdump(len=131): 01 03 00 7f fe 03 a1 00 20 00 00
> 00 00 00 00 00 05 b9 0a 64 80 93 14 3d 57 ca d2 01 18 ef 20 09 21 81 ce
> e5 98 05 0b 53 f0 ee ae 8b 2a 5e d4 f4 2f 81 ce e5 98 05 0b 53 f0 ee ae
> 8b 2a 5e d4 f4 32 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c3 ae
> e1 31 81 da 33 ec 5a 13 93 df 03 c1 f5 75 00 20 41 95 1f 51 7a 69 e2 a3
> 65 2c 46 30 c0 7d fe 4a 1a 22 5b dc fb ad 37 c7 3b c9 9d 99 ca 62 7d 41
> WPA: RX message 1 of Group Key Handshake from 00:13:10:68:4f:1c (ver=1)
> State: GROUP_HANDSHAKE -> GROUP_HANDSHAKE
> WPA: Group Key - hexdump(len=32): [REMOVED]
> WPA: Installing GTK to the driver (keyidx=2 tx=0).
> WPA: RSC - hexdump(len=6): 00 00 00 00 00 00
> wpa_driver_wext_set_key: alg=2 key_idx=2 set_tx=0 seq_len=6 key_len=32
> WPA: Sending EAPOL-Key 2/2
> WPA: TX EAPOL-Key - hexdump(len=99): 01 03 00 5f fe 03 21 00 20 00 00 00
> 00 00 00 00 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 36 43 99
> 35 44 14 2b d4 f5 d1 04 31 bd d1 87 b4 00 00
> WPA: Key negotiation completed with 00:13:10:68:4f:1c [PTK=TKIP GTK=TKIP]
> Cancelling authentication timeout
> State: GROUP_HANDSHAKE -> COMPLETED
> CTRL-EVENT-CONNECTED - Connection to 00:13:10:68:4f:1c completed (auth)
> [id=0 id_str=]
> wpa_driver_wext_set_operstate: operstate 0->1 (UP)
> WEXT: Operstate: linkmode=-1, operstate=6
> EAPOL: External notification - portValid=1
> EAPOL: External notification - EAP success=1
> EAPOL: SUPP_PAE entering state AUTHENTICATING
> EAPOL: SUPP_BE entering state SUCCESS
> EAP: EAP entering state DISABLED
> EAPOL: SUPP_PAE entering state AUTHENTICATED
> EAPOL: SUPP_BE entering state IDLE
> RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
> RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> RX ctrl_iface - hexdump_ascii(len=6):
> 53 54 41 54 55 53 STATUS
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> CTRL-EVENT-TERMINATING - signal 2 received
> Removing interface eth1
> State: COMPLETED -> DISCONNECTED
> wpa_driver_wext_set_operstate: operstate 1->0 (DORMANT)
> WEXT: Operstate: linkmode=-1, operstate=5
> wpa_driver_wext_deauthenticate
> wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
> wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> EAPOL: External notification - portEnabled=0
> EAPOL: SUPP_PAE entering state DISCONNECTED
> EAPOL: SUPP_BE entering state INITIALIZE
> EAPOL: External notification - portValid=0
> wpa_driver_wext_set_wpa
> wpa_driver_wext_set_drop_unencrypted
> wpa_driver_wext_set_countermeasures
> No keys have been configured - skip key clearing
> Cancelling scan request
> Cancelling authentication timeout
> WEXT: Operstate: linkmode=0, operstate=6
>
> ############################################################################
> NETWORKMANAGER
> [root lc4eb7681638218 eap]# iwconfig eth1 essid ATMEL
>
> [root lc4eb7681638218 eap]# iwconfig
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> eth1 unassociated ESSID:"ATMEL" Nickname:"ipw2100"
> Mode:Managed Channel=0 Access Point: Not-Associated
> Bit Rate=0 kb/s Tx-Power:16 dBm
> Retry min limit:7 RTS thr:off Fragment thr:off
> Encryption key:off
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:5 Missed beacon:0
>
> sit0 no wireless extensions.
>
> [root test eap]# ./nm-supplicant-test eth1 wpa_supplicant.conf
> ap_scan: 2
> Key: ssid, Value: "ATMEL"
> Key: scan_ssid, Value: 1
> Key: proto, Value: WPA
> Key: key_mgmt, Value: WPA-PSK
> Key: pairwise, Value: CCMP TKIP
> Key: group, Value: CCMP TKIP WEP104 WEP40
> Key: psk, Value:
> 2fe06ac721b4c2e049589625ae2681278d3d047c9b4f4960e8c239e9f03d4e1f
> SUP: sending command 'INTERFACE_ADD eth1 wext
> /var/run/wpa_supplicant '
> SUP: response was 'OK'
> SUP: sending command 'AP_SCAN 2'
> SUP: response was 'OK'
> SUP: sending command 'ADD_NETWORK'
> SUP: response was '0'
> SUP: sending command 'SET_NETWORK 0 ssid "ATMEL"'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 scan_ssid 1'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 proto WPA'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 key_mgmt WPA-PSK'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 pairwise CCMP TKIP'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 group CCMP TKIP WEP104 WEP40'
> SUP: response was 'OK'
> SUP: sending command 'SET_NETWORK 0 psk
> 2fe06ac721b4c2e049589625ae2681278d3d047c9b4f4960e8c239e9f03d4e1f'
> SUP: response was 'OK'
> SUP: sending command 'ENABLE_NETWORK 0'
> SUP: response was 'OK'
> wpa_supplicant(2177): Global control interface
> '/var/run/wpa_supplicant-global'
> wpa_supplicant(2177): RX global ctrl_iface - hexdump_ascii(len=49):
> wpa_supplicant(2177): 49 4e 54 45 52 46 41 43 45 5f 41 44 44 20 65
> 74 INTERFACE_ADD et
> wpa_supplicant(2177): 68 31 09 09 77 65 78 74 09 2f 76 61 72 2f 72
> 75 h1__wext_/var/ru
> wpa_supplicant(2177): 6e 2f 77 70 61 5f 73 75 70 70 6c 69 63 61 6e
> 74 n/wpa_supplicant
> wpa_supplicant(2177):
> 09 _
> wpa_supplicant(2177): CTRL_IFACE GLOBAL INTERFACE_ADD 'eth1
> wext /var/run/wpa_supplicant '
> wpa_supplicant(2177): Initializing interface 'eth1' conf 'N/A' driver
> 'wext' ctrl_interface '/var/run/wpa_supplicant' bridge 'N/A'
> wpa_supplicant(2177): Initializing interface (2) 'eth1'
> wpa_supplicant(2177): EAPOL: SUPP_PAE entering state DISCONNECTED
> wpa_supplicant(2177): EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> wpa_supplicant(2177): EAPOL: SUPP_BE entering state INITIALIZE
> wpa_supplicant(2177): EAP: EAP entering state DISABLED
> wpa_supplicant(2177): EAPOL: External notification - portEnabled=0
> wpa_supplicant(2177): EAPOL: External notification - portValid=0
> wpa_supplicant(2177): SIOCGIWRANGE: WE(compiled)=20 WE(source)=18
> enc_capa=0xf
> wpa_supplicant(2177): capabilities: key_mgmt 0xf enc 0xf
> wpa_supplicant(2177): WEXT: Operstate: linkmode=1, operstate=5
> wpa_supplicant(2177): b
> wpa_supplicant(2177): wpa_driver_wext_set_wpa
> wpa_supplicant(2177): wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0
> seq_len=0 key_len=0
> wpa_supplicant(2177): wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0
> seq_len=0 key_len=0
> wpa_supplicant(2177): wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0
> seq_len=0 key_len=0
> wpa_supplicant(2177): wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0
> seq_len=0 key_len=0
> wpa_supplicant(2177): wpa_driver_wext_set_countermeasures
> wpa_supplicant(2177): wpa_driver_wext_set_drop_unencrypted
> wpa_supplicant(2177): Setting scan request: 0 sec 100000 usec
> wpa_supplicant(2177): Added interface eth1
> wpa_supplicant(2177): RTM_NEWLINK: operstate=0 ifi_flags=0x1002 ()
> wpa_supplicant(2177): Wireless event: cmd=0x8b06 len=8
> wpa_supplicant(2177): RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> wpa_supplicant(2177): RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> wpa_supplicant(2177): RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> wpa_supplicant(2177): RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=9):
> wpa_supplicant(2177): 41 50 5f 53 43 41 4e 20
> 32 AP_SCAN 2
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=11):
> wpa_supplicant(2177): 41 44 44 5f 4e 45 54 57 4f 52
> 4b ADD_NETWORK
> wpa_supplicant(2177): CTRL_IFACE: ADD_NETWORK
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=26): [REMOVED]
> wpa_supplicant(2177): _NETWORK id=0 name='ssid'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=7): [REMOVED]
> wpa_supplicant(2177): ssid - hexdump_ascii(len=5):
> wpa_supplicant(2177): 41 54 4d 45
> 4c ATMEL
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=25): [REMOVED]
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='scan_ssid'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=1): [REMOVED]
> wpa_supplicant(2177): scan_ssid=1 (0x1)
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=23): [REMOVED]
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='proto'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=3): [REMOVED]
> wpa_supplicant(2177): proto: 0x1
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=30): [REMOVED]
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='key_mgmt'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=7): [REMOVED]
> wpa_supplicant(2177): key_mgmt: 0x2
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=32): [REMOVED]
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='pairwise'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=9): [REMOVED]
> wpa_supplicant(2177): pairwise: 0x18
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=42): [REMOVED]
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='group'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=22): [REMOVED]
> wpa_supplicant(2177): group: 0x1e
> wpa_supplicant(2177):
> wpa_supplicant(2177): CTRL_IFACE: SET_NETWORK id=0 name='psk'
> wpa_supplicant(2177): CTRL_IFACE: value - hexdump_ascii(len=64): [REMOVED]
> wpa_supplicant(2177): PSK - hexdump(len=32): [REMOVED]
> wpa_supplicant(2177): RX ctrl_iface - hexdump_ascii(len=16):
> wpa_supplicant(2177): 45 4e 41 42 4c 45 5f 4e 45 54 57 4f 52 4b 20
> 30 ENABLE_NETWORK 0
> wpa_supplicant(2177): CTRL_IFACE: ENABLE_NETWORK id=0
> wpa_supplicant(2177): Setting scan request: 0 sec 0 usec
> wpa_supplicant(2177): State: DISCONNECTED -> SCANNING
> wpa_supplicant(2177): Trying to associate with SSID 'ATMEL'
> wpa_supplicant(2177): Cancelling scan request
> wpa_supplicant(2177): WPA: clearing own WPA/RSN IE
> wpa_supplicant(2177): Automatic auth_alg selection: 0x1
> wpa_supplicant(2177): WPA: No WPA/RSN IE available from association info
> wpa_supplicant(2177): WPA: Set cipher suites based on configuration
> wpa_supplicant(2177): WPA: Selected cipher suites: group 30 pairwise 24
> key_mgmt 2 proto 1
> wpa_supplicant(2177): WPA: clearing AP WPA IE
> wpa_supplicant(2177): WPA: clearing AP RSN IE
> wpa_supplicant(2177): WPA: using GTK CCMP
> wpa_supplicant(2177): WPA: using PTK CCMP
> wpa_supplicant(2177): WPA: using KEY_MGMT WPA-PSK
> wpa_supplicant(2177): WPA: Set own WPA IE default - hexdump(len=24): dd
> 16 00 50 f2 01 01 00 00 50 f2 04 01 00 00 50 f2 04 01 00 00 50 f2 02
> wpa_supplicant(2177): No keys have been configured - skip key clearing
> wpa_supplicant(2177): wpa_driver_wext_set_drop_unencrypted
> wpa_supplicant(2177): State: SCANNING -> ASSOCIATING
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> ioctl[SIOCGIFADDR]: Cannot assign requested address
> Activation (eth1/wireless): association took too long (>20s), failing
> activation.
> sendmsg(CTRL_IFACE monitor): No such file or directory
> [root test eap]# iwconfig
> lo no wireless extensions.
>
> eth0 no wireless extensions.
>
> eth1 unassociated ESSID:"ATMEL" Nickname:"ipw2100"
> Mode:Managed Channel=0 Access Point: Not-Associated
> Bit Rate=0 kb/s Tx-Power:16 dBm
> Retry min limit:7 RTS thr:off Fragment thr:off
> Encryption key:off
> Power Management:off
> Link Quality:0 Signal level:0 Noise level:0
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
> Tx excessive retries:0 Invalid misc:6 Missed beacon:0
>
> sit0 no wireless extensions.
>
>
>
> Dan Williams wrote:
> > On Wed, 2007-01-24 at 10:15 -0500, Darren Albers wrote:
> >
> >> On 1/24/07, Grant Williamson <traxtopel gmail com> wrote:
> >>
> >>> Dan,
> >>> are there any plans for Network Manager to handle hidden essid's?
> >>> i.e. using wpa_supplicant I can connect with the following config.
> >>>
> >>> ctrl_interface=/var/run/wpa_supplicant
> >>> eapol_version=1
> >>> network={
> >>> ssid="MBI"
> >>> scan_ssid=1
> >>> eap=TLS
> >>> key_mgmt=IEEE8021X
> >>> pairwise=TKIP
> >>> group=WEP104
> >>> identity="traxtopel mbi com"
> >>> ca_cert="/etc/eap/cacert.pem"
> >>> client_cert="etc/eap/key.pem"
> >>> private_key="/etc/eap/key.pem"
> >>> private_key_passwd="whodareswins"
> >>> eapol_flags=3
> >>> }
> >>>
> >>> With networkmanager it never connects(the only way I have ever managed
> >>> to connect was to quickly do a iwconfig eth0 essid MBI and then fingers
> >>> crossed it worked once).
> >>>
> >>>
> >> <snip>
> >>
> >> I don't think the issue is a hidden SSID, I think the problem is using
> >> EAP with WEP which I don't /think/ NetworkManager supports at this
> >> time. Dan, correct me if I am wrong.
> >>
> >
> > Ah, you're right. This is the "compat" mode that allows WEP clients to
> > continue to work with WPA base stations; since WEP clients don't know
> > anything about pairwise keys they can work as normal, but WPA-capable
> > clients can use TKIP/CCMP for all STA<->AP communication.
> >
> > That's likely the problem, yes.
> >
> > Dan
> >
> >
> >
> >
>
> _______________________________________________
> NetworkManager-list mailing list
> NetworkManager-list gnome org
> http://mail.gnome.org/mailman/listinfo/networkmanager-list
[
Date Prev][
Date Next] [
Thread Prev][
Thread Next]
[
Thread Index]
[
Date Index]
[
Author Index]
