Re: NM -- does it actually work?

[Adrian Vasile <yoyo opennet ro>]

ok.. I took Ryan's advice and ran NM with --no-daemon... and without
wpa_supplicant as suggested.

It "fails" to associate to the AP when it's already associated.. thus
getting stuck and... making me hit walls with my head :)

This is the output:
NM: <information>   eth1: Device is fully-supported using driver
'ipw3945'.
NM: <information>   nm_device_init(): waiting for device's worker thread
to start
NM: <information>   nm_device_init(): device's worker thread started,
continuing.
NM: <information>   Now managing wireless (802.11) device 'eth1'.
NM: <information>   Deactivating device eth1.
NM: <information>   eth0: Device is fully-supported using driver 'tg3'.
NM: <information>   nm_device_init(): waiting for device's worker thread
to start
NM: <information>   nm_device_init(): device's worker thread started,
continuing.
NM: <information>   Now managing wired Ethernet (802.3) device 'eth0'.
NM: <information>   Deactivating device eth0.
NM: <information>   Updating allowed wireless network lists.
NM: <WARNING>        nm_dbus_get_networks_cb (): error received:
org.freedesktop.NMInfo.NoNetworks - There are no wireless networks
stored..
NM: <debug info>    [1172262737.561285]
nm_device_802_11_wireless_get_activation_ap (): Forcing AP 'opennet'
NM: <information>   User Switch: /org/freedesktop/NM/Devices/eth1 /
opennet
NM: <information>   Deactivating device eth1.
NM: <information>   Device eth1 activation scheduled...
NM: <information>   Activation (eth1) started...
NM: <information>   Activation (eth1) Stage 1 of 5 (Device Prepare)
scheduled...
NM: <information>   Activation (eth1) Stage 1 of 5 (Device Prepare)
started...
NM: <information>   Activation (eth1) Stage 2 of 5 (Device Configure)
scheduled...
NM: <information>   Activation (eth1) Stage 1 of 5 (Device Prepare)
complete.
NM: <information>   Activation (eth1) Stage 2 of 5 (Device Configure)
starting...
NM: <information>   Activation (eth1/wireless): access point 'opennet'
is unencrypted, no key needed.
NM: <information>   SUP: sending command 'INTERFACE_ADD eth1
wext    /var/run/wpa_supplicant '
NM: <information>   SUP: response was 'OK'
NM: <information>   SUP: sending command 'AP_SCAN 1'
NM: <information>   SUP: response was 'OK'
NM: <information>   SUP: sending command 'ADD_NETWORK'
NM: <information>   SUP: response was '0'
NM: <information>   SUP: sending command 'SET_NETWORK 0 ssid
6f70656e6e6574'
NM: <information>   SUP: response was 'OK'
NM: <information>   SUP: sending command 'SET_NETWORK 0 key_mgmt NONE'
NM: <information>   SUP: response was 'OK'
NM: <information>   SUP: sending command 'ENABLE_NETWORK 0'
NM: <information>   SUP: response was 'OK'
NM: <information>   Activation (eth1) Stage 2 of 5 (Device Configure)
complete.
NM: <information>   Activation (eth1/wireless): association took too
long (>40s), failing activation.
NM: <information>   Activation (eth1) failed for access point (opennet)
NM: <information>   Activation (eth1) failure scheduled...
NM: <information>   Activation (eth1) failed.
NM: <information>   Deactivating device eth1.
sendmsg(CTRL_IFACE monitor): No such file or directory

maybe someone saw this before...

Adrian