Re: [gtk-osx-users] Another jhbuild problem

[John Ralls <jralls ceridwen us>]

Very good.

RUSTUP isn't RUSTUP_HOME, which needs to point to where the toolchains live, something I didn't really 
understand when I wrote that section of gtk-osx-setup.sh. I think I know how to fix it.

Regards,
John Ralls

> On Aug 26, 2021, at 4:21 AM, David Price <david dcprice ca> wrote:
>
>
> Hello
>
> Success!
>
> I changed the relevant line in jhbuild to read : export RUSTUP_HOME="/Users/david/.rustup"
>
> and jhbuild finished building successfully.
>
> The "which rustup" command in my Terminal returns /Users/david/.cargo/bin/rustup
>
> whereas I changed jhbuild to look for the .rustup directory, not the .cargo one.
>
> I noticed the gtk-osx-setup.sh also uses RUSTUP='which rustup' so perhaps it is using the .cargo directory 
> as well.
>
> Thank you for your help, John.
>
>     David
>
>
>
> On 2021-08-25 11:05 p.m., John Ralls wrote:
> > No, I recommend figuring out why the RUSTUP_HOME environment variable in ~/.new_local/bin/jhbuild isn't 
> > finding your rust installation and fixing it so that it does. If you can also figure out how to get 
> > gtk-osx-setup.sh to configure jhbuild correctly in the first place I'll gladly apply it.
> >
> > Regards,
> > John Ralls
> >
> >
> > > On Aug 25, 2021, at 1:37 PM, David Price <david dcprice ca> wrote:
> > >
> > >
> > > Hi
> > >
> > > I already have Rust installed (~/.rustup) and have been using it for a while. Do you recommend 
> > > uninstalling it, then re-running jhbuild?
> > >
> > >     David
> > >
> > >
> > >
> > > On 2021-08-25 4:24 p.m., John Ralls wrote:
> > > > > On Aug 25, 2021, at 12:28 PM, David Price via gtk-osx-users-list <gtk-osx-users-list gnome org> wrote:
> > > > >
> > > > >
> > > > > Hello again. Sorry to bother you again but I have another problem, this time in 31/33 librsvg.
> > > > >
> > > > > I tried rerunning the phase build but it still failed.
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > *** Building librsvg *** [31/33]
> > > > > make -j 5
> > > > > make  all-recursive
> > > > > make[1]: Entering directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > > Making all in .
> > > > > make[2]: Entering directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > >   CC       _rsvg_dummy.lo
> > > > > cd /Users/david/gtk/source/librsvg-2.51.0 &&     \
> > > > > PKG_CONFIG_ALLOW_CROSS=1                        \
> > > > > PKG_CONFIG='/Users/david/gtk/inst/bin/pkg-config'         \
> > > > > CARGO_TARGET_DIR=/Users/david/.cache/jhbuild/build/librsvg-2.51.0/target             \
> > > > > cargo --locked build   --release --bin rsvg-convert
> > > > > error: no override and no default toolchain set
> > > > > make[2]: *** [Makefile:1599: 
> > > > > /Users/david/.cache/jhbuild/build/librsvg-2.51.0/target/release/rsvg-convert] Error 1
> > > > > make[2]: *** Waiting for unfinished jobs....
> > > > > make[2]: Leaving directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > > make[1]: *** [Makefile:1105: all-recursive] Error 1
> > > > > make[1]: Leaving directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > > make: *** [Makefile:738: all] Error 2
> > > > > *** Error during phase build of librsvg: ########## Error running make -j 5  *** [31/33]
> > > > >
> > > > >   [1] Rerun phase build
> > > > >   [2] Ignore error and continue to install
> > > > >   [3] Give up on module
> > > > >   [4] Start shell
> > > > >   [5] Reload configuration
> > > > >   [6] Go to phase "wipe directory and start over"
> > > > >   [7] Go to phase "configure"
> > > > >   [8] Go to phase "clean"
> > > > >   [9] Go to phase "distclean"
> > > > > choice:
> > > > Rust can't find its toolchain. It would normally look in $RUSTUP_HOME; in a clean macOS that's set in 
> > > > ~/.new_local/bin/jhbuild to ~/.new_local and the toolchains should be in ~/.new_local/toolchains. In the 
> > > > unlikely event that you already had rust installed gtk-osx-setup.sh would have tried to use the 
> > > > already-installed one instead.
> > > >
> > > > Regards,
> > > > John Ralls