Re: [gtk-osx-users] Another jhbuild problem

[David Price <david dcprice ca>]

Hello

Success!

I changed the relevant line in jhbuild to read : export 
RUSTUP_HOME="/Users/david/.rustup"

and jhbuild finished building successfully.

The "which rustup" command in my Terminal returns 
/Users/david/.cargo/bin/rustup

whereas I changed jhbuild to look for the .rustup directory, not the 
.cargo one.

I noticed the gtk-osx-setup.sh also uses RUSTUP='which rustup' so 
perhaps it is using the .cargo directory as well.

Thank you for your help, John.

    David



On 2021-08-25 11:05 p.m., John Ralls wrote:
> No, I recommend figuring out why the RUSTUP_HOME environment variable in ~/.new_local/bin/jhbuild isn't 
> finding your rust installation and fixing it so that it does. If you can also figure out how to get 
> gtk-osx-setup.sh to configure jhbuild correctly in the first place I'll gladly apply it.
>
> Regards,
> John Ralls
>
>
> > On Aug 25, 2021, at 1:37 PM, David Price <david dcprice ca> wrote:
> >
> >
> > Hi
> >
> > I already have Rust installed (~/.rustup) and have been using it for a while. Do you recommend uninstalling 
> > it, then re-running jhbuild?
> >
> >      David
> >
> >
> >
> > On 2021-08-25 4:24 p.m., John Ralls wrote:
> > > > On Aug 25, 2021, at 12:28 PM, David Price via gtk-osx-users-list <gtk-osx-users-list gnome org> wrote:
> > > >
> > > >
> > > > Hello again. Sorry to bother you again but I have another problem, this time in 31/33 librsvg.
> > > >
> > > > I tried rerunning the phase build but it still failed.
> > > >
> > > >
> > > >
> > > >
> > > > *** Building librsvg *** [31/33]
> > > > make -j 5
> > > > make  all-recursive
> > > > make[1]: Entering directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > Making all in .
> > > > make[2]: Entering directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > >    CC       _rsvg_dummy.lo
> > > > cd /Users/david/gtk/source/librsvg-2.51.0 &&     \
> > > > PKG_CONFIG_ALLOW_CROSS=1                        \
> > > > PKG_CONFIG='/Users/david/gtk/inst/bin/pkg-config'         \
> > > > CARGO_TARGET_DIR=/Users/david/.cache/jhbuild/build/librsvg-2.51.0/target             \
> > > > cargo --locked build   --release --bin rsvg-convert
> > > > error: no override and no default toolchain set
> > > > make[2]: *** [Makefile:1599: /Users/david/.cache/jhbuild/build/librsvg-2.51.0/target/release/rsvg-convert] 
> > > > Error 1
> > > > make[2]: *** Waiting for unfinished jobs....
> > > > make[2]: Leaving directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > make[1]: *** [Makefile:1105: all-recursive] Error 1
> > > > make[1]: Leaving directory '/Users/david/.cache/jhbuild/build/librsvg-2.51.0'
> > > > make: *** [Makefile:738: all] Error 2
> > > > *** Error during phase build of librsvg: ########## Error running make -j 5  *** [31/33]
> > > >
> > > >    [1] Rerun phase build
> > > >    [2] Ignore error and continue to install
> > > >    [3] Give up on module
> > > >    [4] Start shell
> > > >    [5] Reload configuration
> > > >    [6] Go to phase "wipe directory and start over"
> > > >    [7] Go to phase "configure"
> > > >    [8] Go to phase "clean"
> > > >    [9] Go to phase "distclean"
> > > > choice:
> > > Rust can't find its toolchain. It would normally look in $RUSTUP_HOME; in a clean macOS that's set in 
> > > ~/.new_local/bin/jhbuild to ~/.new_local and the toolchains should be in ~/.new_local/toolchains. In the 
> > > unlikely event that you already had rust installed gtk-osx-setup.sh would have tried to use the 
> > > already-installed one instead.
> > >
> > > Regards,
> > > John Ralls