Re: [Gimp-developer] Nightly Builds

[drawoc <drawoc darkrefraction com>]

I run the scripts under Debian testing regularly, so if you choose
Debian or one of its derivatives you shouldn't have a hard time.

If you're still fairly new to linux though, you probably want to go
with something other than straight Debian. Linux Mint is my personal
favorite of the more user-friendly distros (and it's debian-derived).
http://www.linuxmint.com/
You might want to go with eg. the xfce version of mint as it should be
faster than the cinnamon or mate based desktops.

Anyway, once you have one of those distros installed, you can install
most of the required packages like this:
sudo apt-get install build-essential mingw-w64 git jhbuild automake
autoconf libtool libgtk2.0-dev

Then just follow the README in my git repo,

  -- drawoc

On Tue, Aug 14, 2012 at 5:09 PM, Jari Niskala <jariniskala gmail com> wrote:
> Ah, that explains it :) I tried with the latest and I'm still getting the
> same problem.
>
> There were a lot of issues discussed with jhbuild on Windows so I think I'll
> just get Linux running on a VM to save myself a lot of pain in the short and
> long run. I can retry this later when I'm more familiar with Gimp and the
> whole build process...
>
> Do you have a recommendation on the flavor of Linux? Or on the setup in
> general? I'm 'ok' on Linux but definitely not an expert.
>
> Thanks!!
>
> -----Original Message-----
> From: drawoc [mailto:drawoc darkrefraction com]
> Sent: Tuesday, August 14, 2012 1:48 PM
> To: Jari Niskala
> Cc: gimp-developer-list gnome org
> Subject: Re: [Gimp-developer] Nightly Builds
>
> Try this:
> Pull my latest changes from git, and then do:
> export PYTHON="/c/Python27/bin/python.exe"
> (I'm not sure where your python exe is, so change
> "/c/Python27/bin/python.exe" to the location of the actual exe) Then try
> running the script again.
> Hopefully that will work.
>
> As a side note, I've actually never successfully compiled the GIMP directly
> on windows before, only cross compiled for Windows from Linux. (So you're
> trying something new.)
>
> -- drawoc
>
> On Tue, Aug 14, 2012 at 1:27 PM, Jari Niskala <jariniskala gmail com> wrote:
>> Thanks drawoc!
>>
>> I'm running into some problems that I'm trying to work through but
>> perhaps you or someone else has run into this before and can point me
>> in the right direction (or point out what's wrong with my setup)...
>>
>> Here's the error and afterwards I have listed all the steps I have
>> taken to try to get my environment to be able to run the build script:
>>
>> Jari@Jari-PC /gimp
>> $ build
>> I: unknown keys defined in configuration file: mingw_tool_prefix,
>> mingw_tools, searchprefix, fullpath_tool, flavour_cfla gs, module,
>> tool, flavour_opt, flavour, mingw_tools_args, flavour_ext Traceback
>> (most recent call last):
>>   File "C:/mingw/msys/1.0/bin/jhbuild", line 31, in <module>
>>     jhbuild.main.main(sys.argv[1:])
>>   File "C:/mingw/msys/1.0/jhbuild\jhbuild\main.py", line 130, in main
>>     config = jhbuild.config.Config(options.configfile)
>>   File "C:/mingw/msys/1.0/jhbuild\jhbuild\config.py", line 205, in
> __init__
>>     self.setup_env()
>>   File "C:/mingw/msys/1.0/jhbuild\jhbuild\config.py", line 429, in
> setup_env
>>     get_stderr = False).strip()
>>   File "C:/mingw/msys/1.0/jhbuild\jhbuild\utils\cmds.py", line 63, in
>> get_output
>>     **kws)
>>   File "C:/mingw/msys/1.0/jhbuild\jhbuild\utils\subprocess_win32.py",
>> line 112, in __init__
>>     elif not command[0].endswith('.exe') or kws['shell']:
>> KeyError: 'shell'
>>
>>
>>
>> 1. Install mingw, choose latest packages, c/c++ compiler, msys and
>> developer kit.
>>
>> 2. Install mingw64
>> http://mingw-w64.sourceforge.net/
>>
>> Choose the latest w32 build e.g.
>> mingw32-w32-bin_i686-mingw_xxxxxxxx.zip
>> http://sourceforge.net/projects/mingw-w64/files/Toolchains%20targettin
>> g%20Wi
>> n32/Automated%20Builds/
>>
>> Extract it to your machine on top of mingw, e.g. c:\mingw
>>
>> 3. Install Python27
>> Add python to your path (msys/1.0/etc/profile):
>> export PATH="$PATH:/c/Python27"
>>
>> 4. Get some needed packages
>> mingw-get.exe install msys-wget
>> mingw-get.exe install msys-openssl
>> mingw-get.exe install msys-unzip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/pkg-config_
>> 0.26-1
>> _win32.zip
>> unzip pkg-config_0.26-1_win32.zip
>> rm pkg-config_0.26-1_win32.zip
>>
>> wget
>>
> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/pkg-config-dev_0.
>> 26-1_win32.zip
>> unzip pkg-config-dev_0.26-1_win32.zip
>> rm pkg-config-dev_0.26-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/gnome-common/2.28/gnome-
>> common
>> -dev_2.28.0-1_win32.zip
>> unzip gnome-common-dev_2.28.0-1_win32.zip
>> rm gnome-common-dev_2.28.0-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/gnome-common/2.28/gnome-
>> common
>> _2.28.0-1_win32.zip
>> unzip gnome-common_2.28.0-1_win32.zip
>> rm gnome-common_2.28.0-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/intltool/0.40/intltool-d
>> ev_0.4
>> 0.4-1_win32.zip
>> unzip intltool-dev_0.40.4-1_win32.zip
>> rm intltool-dev_0.40.4-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/intltool/0.40/intltool_0
>> .40.4-
>> 1_win32.zip
>> unzip intltool_0.40.4-1_win32.zip
>> rm intltool_0.40.4-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/glib/2.28/glib-dev_2.28.
>> 8-1_wi
>> n32.zip
>> unzip glib-dev_2.28.8-1_win32.zip
>> rm glib-dev_2.28.8-1_win32.zip
>>
>> wget
>>
> http://ftp.gnome.org/pub/GNOME/binaries/win32/glib/2.28/glib_2.28.8-1_win32.
>> zip
>> unzip glib_2.28.8-1_win32.zip
>> rm glib_2.28.8-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/gettext-run
>> time-d
>> ev_0.18.1.1-2_win32.zip
>> unzip gettext-runtime-dev_0.18.1.1-2_win32.zip
>> rm gettext-runtime-dev_0.18.1.1-2_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/gettext-run
>> time_0
>> .18.1.1-2_win32.zip
>> unzip gettext-runtime_0.18.1.1-2_win32.zip
>> rm gettext-runtime_0.18.1.1-2_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/gnome-doc-utils/0.12/gno
>> me-doc
>> -utils-0.12.0.zip
>> unzip gnome-doc-utils-0.12.0.zip
>> rm gnome-doc-utils-0.12.0.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/libxml2-dev
>> _2.7.7
>> -1_win32.zip
>> unzip libxml2-dev_2.7.7-1_win32.zip
>> rm libxml2-dev_2.7.7-1_win32.zip
>>
>> wget
>> http://ftp.gnome.org/pub/GNOME/binaries/win32/dependencies/libxml2_2.7
>> .7-1_w
>> in32.zip
>> unzip libxml2_2.7.7-1_win32.zip
>> rm libxml2_2.7.7-1_win32.zip
>>
>>
>> 5. Adjust ACLOCAL_FLAGS
>> export ACLOCAL_FLAGS="-I /share/aclocal"
>>
>> 6. Install msysgit to c:\git. When asked, choose the 'Use Git Bash only'
>> option (avoid adding anything to the PATH). In the line ending
>> conversions choice, pick "Checkout as-is, commit Unix-style line endings"
>> Add git/bin to the end of your path (msys/1.0/etc/profile):
>> export PATH="$PATH:/c/git/bin"
>>
>> 7. jhbuild needs to know shell location to be able to run it export
>> SHELL=/bin/sh
>>
>> 8. Install jhbuild http://afuera.me.uk/jhbuild-windows/
>> git clone git://gitorious.org/jhbuild/jhbuild.git
>> cd jhbuild
>> ./autogen-sh (not sure if this is necessary) make -f Makefile.windows
>> make install # create .jhbuildrc file as described on the jhbuild
>> windows page jhbuild sanitycheck (mine is still complaining about
>> gettext and xml
>> catalog)
>> jhbuild bootstrap
>> jhbuild build (some failures here still with libxml2)
>>
>> 11. Get the gimp windows jhbuild
>> https://github.com/drawoc/windows-gimp-jhbuild. Follow directions in
>> README
>>
>>
>> -----Original Message-----
>> From: drawoc [mailto:drawoc darkrefraction com]
>> Sent: Friday, August 10, 2012 5:25 PM
>> To: Jari Niskala
>> Cc: gimp-developer-list gnome org
>> Subject: Re: [Gimp-developer] Nightly Builds
>>
>> I just added a README to the github repository in my first email.
>>
>> Let me know if the scripts give you any trouble.
>>
>>   -- drawoc
>>
>> On Thu, Aug 9, 2012 at 5:13 PM, Jari Niskala <jariniskala gmail com>
> wrote:
>>> That's great drawoc!
>>>
>>> Any chance you have any writeup/info on how to setup to run this locally?
>>> Any info, no matter how small greatly appreciated.
>>>
>>> Thanks!
>>>
>>> -Jari
>>>
>>> -----Original Message-----
>>> From: gimp-developer-list-bounces gnome org
>>> [mailto:gimp-developer-list-bounces gnome org] On Behalf Of drawoc
>>> Sent: Thursday, August 09, 2012 1:10 PM
>>> To: gimp-developer-list gnome org
>>> Subject: [Gimp-developer] Nightly Builds
>>>
>>> I've set up a machine to do start doing nightly builds of the GIMP
>>> for Windows.
>>>
>>> Anyone who's interested can find them here:
>>> http://nightly.darkrefraction.com/gimp/
>>>
>>> I've also uploaded my jhbuild scripts to github:
>>> https://github.com/drawoc/windows-gimp-jhbuild
>>>
>>>   -- drawoc
>>> _______________________________________________
>>> gimp-developer-list mailing list
>>> gimp-developer-list gnome org
>>> https://mail.gnome.org/mailman/listinfo/gimp-developer-list
>>>
>>
>