GNOME.org
 

Re: [Evolution] Evo 1.2 and Visor sync - USB

I am including the printout of several commands for my system, and the
steps that I have used to determine why the Visor will not connect.

A.  SYSTEM DETAILS
B.  STEPS ATTEMPTED
C.  DETAIL INFORMATION BY LINUX DISTRIBUTION


1.  SYSTEM DETAILS
Mandrake 9, 8.2
Red Hat 8.0
Evolution 1.0.8, 1.2
Dell Latitude C600 Laptop
Compaq Presario Desktop
Handspring Visor Pro USB

I have tried to connect my visor to two different computers, using MDK
8.2 on the desktop, and MDK 9, and RH 8 on the laptop.  On the laptop, I
tried Evolution 1.0.8, & 1.2 in Red Hat, and 1.2 in Mandrake, and have
not been able to get the Visor to synchronize.  MDK 8.2 and 9 and RH 8
have all the modules (i.e. visor and usb) needed for the Visor to
synchronize, but I cannot get it to synchronize.

In RH 8, neither the Pilot tools in RH nor Evolution will function, and
allow me to change settings.  Several commands, lsmod & coldsync are
disabled in the Personal Desktop version of Red Hat.


B.  STEPS ATTEMPTED
I have:
1.  Changed permissions (verified permissions were correct)
2.  dmesg
3.  lsmod (when available)
4.  cat /proc/devices
5.  cat /proc/bus/usb/devices
6.  pilot-xfer /dev/usb/ttyUSB1 â-list




C.  DETAIL INFORMATION BY LINUX DISTRIBUTION
With RH 8, it 

chmod 775 /dev/usb/ttyUSB0
chmod 775 /dev/usb/ttyUSB1
chmod 775 /dev/usb/tts/0
chmod 775 /dev/usb/tts/1


lsmod - does not work in RH 8

coldsync â not functioning in RH 8

In RH 8, to use pilot-xfer /dev/usb/ttyUSB1 âlist, I needed to make a
symbolic link. From dmesg, I saw that the Handspring was connected on
USB0 and USB1. The symbolic link for my system is:

# ln -s /dev/usb/ttyUSB1 /dev/pilot


# gpilotd
gpilotd-Message: gnome-pilot 0.1.65 starting...
gpilotd-Message: compiled for pilot-link version 0.11.3
gpilotd-Message: compiled with [VFS] [GOAD] [USB] [IrDA] [Netw
GnomeUI-WARNING **: While connecting to session manager:
Authentication Rejected, reason : None of the authentication p and
host-based authentication failed.


gpilotd-WARNING **: Number of devices is configured to 0
gpilotd-WARNING **: No accessible devices available
gpilotd-WARNING **: Number of pilots is configured to 0
gpilotd-Message: Activating CORBA server
gpilotd-Message: Exiting (caught SIGINT)...









MANDRAKE 8.2  1 mem
1.  cat /proc/devices
2.  cat /proc/bus/usb/devices
3.  dmesg   (This 
4.  pilot-xfer /dev/usb/tts/1 â-list


1.  cat /proc/devices
  2 pty/m%d
  3 pty/s%d
  4 tts/%d
  5 cua/%d
  6 lp
  7 vcs
 10 misc
 13 input
 14 sound
 21 sg
 29 fb
128 ptm
136 pts/%d
162 raw
180 usb
188 usb/tts/%d
195 nvidia

Block devices:
  1 ramdisk
  2 fd
  3 ide0
  9 md
 11 sr
 22 ide1
[root localhost sysconfig]#





2.  cat /proc/bus/usb/devices   (there are 4 USB devices connected,
keyboard, mouse, Visor & APC powerbackup)

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB UHCI Root Hub
S:  SerialNumber=2460
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms
T:  Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 16 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=051d ProdID=0002 Rev= 1.00
S:  Manufacturer=American Power Conversion
S:  Product=Back-UPS 500 FW: 6.4.D USB FW: c1
S:  SerialNumber=JB0217025161
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 30mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=hid
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl= 10ms
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=329/900 us (37%), #Int=  3, #Iso=  0
D:  Ver= 1.00 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB UHCI Root Hub
S:  SerialNumber=2440
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=255ms
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=049f ProdID=000e Rev= 1.02
S:  Manufacturer=Chicony
S:  Product=Compaq Internet Keyboard
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=01 Driver=keyboard
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl= 10ms
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=hid
E:  Ad=82(I) Atr=03(Int.) MxPS=   8 Ivl= 10ms
T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  5 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=045e ProdID=0040 Rev= 1.21
S:  Manufacturer=Microsoft
S:  Product=Microsoft Wheel Mouse OpticalÂ
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=hid
E:  Ad=81(I) Atr=03(Int.) MxPS=   4 Ivl= 10ms
[root localhost sysconfig]#



3.  dmesg
iver
hub.c: USB new device connect on bus2/2, assigned device number 2
usb-uhci.c: interrupt, status 3, frame# 1168
hiddev1: USB HID v1.00 Device [American Power Conversion Back-UPS 500
FW: 6.4.D USB FW: c1 ] on usb2:2.0
Adding Swap: 2097136k swap-space (priority -1)
nvidia: loading NVIDIA NVdriver Kernel Module  1.0-2802  Tue Mar  5
06:26:45 PST 2002
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: LITE-ON   Model: LTR-24102B        Rev: 5QSB
  Type:   CD-ROM                             ANSI SCSI revision: 02
eepro100.c:v1.09j-t 9/29/99 Donald Becker
http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin
<saw saw sw com sg> and othersPCI: Found IRQ 10 for device 02:08.0
eth0: OEM i82557/i82558 10/100 Ethernet, 00:08:02:0F:D2:D5, I/O at
0x1400, IRQ 10.
  Board assembly 011345-001, Physical connectors present: RJ45
  Primary interface chip i82555 PHY #1.
  General self-test: passed.
  Serial sub-system self-test: passed.
  Internal registers self-test: passed.
  ROM checksum self-test: passed (0x04f4518b).
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: Legacy device
IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
IPVS: ipvs loaded.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: Legacy device
lp0: using parport0 (polling).
devfs_mk_dir(sound): using old entry in dir: dffc55c0 ""
Intel 810 + AC97 Audio, version 0.21, 03:22:49 Mar 15 2002
PCI: Found IRQ 5 for device 00:1f.5
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH2 found at IO 0x2400 and 0x2000, IRQ 5
i810_audio: Audio Controller supports 6 channels.
ac97_codec: AC97 Audio codec, id: 0x4144:0x5360 (Analog Devices AD1885)
i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not
present), total channels = 2
i810_audio: setting clocking to 41260
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
Splash status on console 0 changed to off
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Intel i845 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
NVRM: AGPGART: unknown chipset
NVRM: AGPGART: aperture: 64M @ 0xf8000000
NVRM: AGPGART: aperture mapped from 0xf8000000 to 0xe487b000
NVRM: AGPGART: mode 4x
NVRM: AGPGART: allocated 16 pages
NVRM: AGPGART: freed 16 pages
NVRM: AGPGART: backend released
NVRM: AGPGART: unknown chipset
NVRM: AGPGART: aperture: 64M @ 0xf8000000
NVRM: AGPGART: aperture mapped from 0xf8000000 to 0xe4838000
NVRM: AGPGART: mode 4x
NVRM: AGPGART: allocated 16 pages
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
PCI: Found IRQ 5 for device 02:0a.0
eth1: ADMtek Comet rev 17 at 0x1000, 00:04:5A:5A:1C:CB, IRQ 5.
usb.c: USB disconnect on device 2
hub.c: USB new device connect on bus2/2, assigned device number 3
usb-uhci.c: interrupt, status 3, frame# 850
hiddev1: USB HID v1.00 Device [American Power Conversion Back-UPS 500
FW: 6.4.D USB FW: c1 ] on usb2:3.0
usb-uhci.c: interrupt, status 3, frame# 1804
usb.c: USB disconnect on device 2
hub.c: USB new device connect on bus1/1, assigned device number 4
input0: Chicony Compaq Internet Keyboard on usb1:4.0
input1,hiddev0: USB HID v1.10 Pointer [Chicony Compaq Internet Keyboard]
on usb1:4.1
cdrom: open failed.
cdrom: open failed.
cdrom: open failed.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cdrom: open failed.
lp0: compatibility mode
lp0: compatibility mode
hub.c: connect-debounce failed, port 1 disabled
hub.c: USB new device connect on bus2/1, assigned device number 4
usb.c: USB device 4 (vend/prod 0x82d/0x100) is not claimed by any active
driver.
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for Handspring Visor
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usbserial.c: USB Serial support registered for Palm 4.0
usbserial.c: USB Serial support registered for Sony Clià 3.5
usbserial.c: USB Serial support registered for Sony Clià 4.0
visor.c: USB HandSpring Visor, Palm m50x, Sony Clià driver v1.5
usb.c: USB disconnect on device 4
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
cdrom: open failed.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
cdrom: open failed.
lp0: compatibility mode
i810_audio: drain_dac, dma timeout?
cdrom: open failed.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
lp0: compatibility mode
cdrom: open failed.
cdrom: open failed.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
cdrom: open failed.
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
NVRM: AGPGART: allocated 258 pages
lp0: compatibility mode
lp0: compatibility mode
NVRM: AGPGART: freed 258 pages
lp0: compatibility mode
lp0: compatibility mode
hub.c: USB new device connect on bus2/1, assigned device number 5
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 5
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 6
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 6
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 7
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 7
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 8
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 8
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 9
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 9
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 10
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 10
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 11
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 11
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 12
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 12
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
lp0: compatibility mode
hub.c: USB new device connect on bus2/1, assigned device number 13
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 13
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 14
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 14
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 15
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 15
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
usb.c: USB disconnect on device 3
usb.c: USB disconnect on device 3
hub.c: USB new device connect on bus2/2, assigned device number 16
usb-uhci.c: interrupt, status 3, frame# 1379
hiddev1: USB HID v1.00 Device [American Power Conversion Back-UPS 500
FW: 6.4.D USB FW: c1 ] on usb2:16.0
hub.c: USB new device connect on bus1/2, assigned device number 5
usb-uhci.c: interrupt, status 3, frame# 497
input2: USB HID v1.00 Mouse [Microsoft Microsoft Wheel Mouse OpticalÂ]
on usb1:5.0
hub.c: USB new device connect on bus2/1, assigned device number 17
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 17
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1
hub.c: USB new device connect on bus2/1, assigned device number 18
usbserial.c: Handspring Visor converter detected
visor.c: Handspring Visor: Number of ports: 2
visor.c: Handspring Visor: port 1, is for Generic use and is bound to
ttyUSB0
visor.c: Handspring Visor: port 2, is for HotSync use and is bound to
ttyUSB1
usbserial.c: Handspring Visor converter now attached to ttyUSB0 (or
usb/tts/0 for devfs)
usbserial.c: Handspring Visor converter now attached to ttyUSB1 (or
usb/tts/1 for devfs)
usb.c: USB disconnect on device 18
usbserial.c: Handspring Visor converter now disconnected from ttyUSB0
usbserial.c: Handspring Visor converter now disconnected from ttyUSB1



4.   pilot-xfer /dev/pilot --list
No $PILOTPORT specified and no -p <port> given.
Defaulting to '/dev/pilot'


   Listening to port: /dev/pilot

   Please press the HotSync button now... Connected

Reading list of databases in RAM...
CityTimeDB
Datebk3HDB
HSAdvCalcDB
AddressDB
DatebookDB
LauncherDB
MailDB
MemoDB
ConnectionDB
NetworkDB
ToDoDB
Graffiti
AddressCitiesDB
AddressCompaniesDB
AddressCountriesDB
psysLaunchDB
Graffiti ShortCuts
Unsaved Preferences
Net Prefs
System MIDI Sounds
Saved Preferences
AddressStatesDB
AddressTitlesDB

List complete. 23 files found.
Time elapsed: 0:00:01
[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]