3G USB support for NM 0.7 (II)

From: Keith Smith <keithsmith2 gmail com>
To: dcbw redhat com, jklimes redhat com, networkmanager-list gnome org
Subject: 3G USB support for NM 0.7 (II)
Date: Sun, 28 Feb 2010 12:58:52 -0500

Hi,

  I am happy to report that 3G Sierra Wireless 598 CDMA modem
(EVDO-RevA) is working very well with Ubuntu 9.04 Netbook remix.  I
downloaded the 1G image for USB key, booted off it, then installed it
into a new partition...  HOWEVER, the 9.04 netbook remix runs very,
very slow (15 seconds to switch apps) on my Dell Inspiron Mini 1210.
After a quick search, I found that others also had poor performance,
so now I am going to replace it with the 9.04 lpia distro.  Other
distros are 9.04 desktop.  Since the 8.04 hardy was a lpia distro, and
it was working well, I am going to try it out...

  Before reverting to another distro, I wanted to document the
configuration that is working.

  Note: I was reading that Sierra Wireless have made upgrades to the
kernel which allow it to detect their device correctly in 9.04
(2.6.28-11-generic), with Sierra Wireless driver version v.1.3.2.  The
driver even detects the USB storage on the modem and mounts it as a
SCSI drive.  USB /dev/usbtty0,1,2,3 appear.

  Reading some of the Sierra wireless posts, they have issues with
9.10, and do not support distro 9.10 for their devices....TBC.

  The operation I found is, when the device is installed, it shows up
in the network manager list as an "auto CDMA", then I have to select
"Connect".  It does connect, and remains connected even if I disable
my Wi-Fi and re-enable it... I would have assumed that it should
detect that prevously available Wi-Fi has returned and at least try to
switch back to Wi-Fi.  The reason I mention that is for a non
technical user, once the CDMA is active, they will stay on the $$$
expensive connection until they manually disconnect...  I suppose that
one simply has to pull out the USB modem to disconnect....

  I would also like to know if there is a way to log the amount of
data downloaded / uploaded via the 3G device (ie: don't go over 1GB
per month = $$$)

Thanks!
Keith.

[    0.000000] BIOS EBDA/lowmem at: 00097000/00097000
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 2.6.28-11-generic (buildd palmer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009 (Ubuntu 2.6.28-11.42-generic)
[    0.000000] KERNEL supported cpus:
[    0.000000]   Intel GenuineIntel
[    0.000000]   AMD AuthenticAMD
[    0.000000]   NSC Geode by NSC
[    0.000000]   Cyrix CyrixInstead
[    0.000000]   Centaur CentaurHauls
[    0.000000]   Transmeta GenuineTMx86
[    0.000000]   Transmeta TransmetaCPU
[    0.000000]   UMC UMC UMC UMC
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 0000000000097000 (usable)
[    0.000000]  BIOS-e820: 0000000000097000 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003f6b0000 (usable)
[    0.000000]  BIOS-e820: 000000003f6b0000 - 000000003f6c0000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003f6c0000 - 000000003f6c3000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003f6c3000 - 0000000040000000 (reserved)
[    0.000000]  BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] DMI present.
[    0.000000] last_pfn = 0x3f6b0 max_arch_pfn = 0x100000
[    0.000000] Scanning 2 areas for low memory corruption
[    0.000000] modified physical RAM map:
[    0.000000]  modified: 0000000000000000 - 0000000000002000 (usable)
[    0.000000]  modified: 0000000000002000 - 0000000000006000 (reserved)
[    0.000000]  modified: 0000000000006000 - 0000000000007000 (usable)
[    0.000000]  modified: 0000000000007000 - 0000000000010000 (reserved)
[    0.000000]  modified: 0000000000010000 - 000000000008a000 (usable)
[    0.000000]  modified: 0000000000097000 - 00000000000a0000 (reserved)
[    0.000000]  modified: 00000000000d0000 - 0000000000100000 (reserved)
[    0.000000]  modified: 0000000000100000 - 000000003f6b0000 (usable)
[    0.000000]  modified: 000000003f6b0000 - 000000003f6c0000 (ACPI data)
[    0.000000]  modified: 000000003f6c0000 - 000000003f6c3000 (ACPI NVS)
[    0.000000]  modified: 000000003f6c3000 - 0000000040000000 (reserved)
[    0.000000]  modified: 00000000e0000000 - 00000000f0000000 (reserved)
[    0.000000]  modified: 00000000fec00000 - 00000000fec10000 (reserved)
[    0.000000]  modified: 00000000fed00000 - 00000000fed00400 (reserved)
[    0.000000]  modified: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  modified: 00000000ffb80000 - 0000000100000000 (reserved)
[    0.000000] kernel direct mapping tables up to 373fe000 @ 10000-16000
[    0.000000] RAMDISK: 378c0000 - 37fef75e
[    0.000000] Allocated new RAMDISK: 00881000 - 00fb075e
[    0.000000] Move RAMDISK from 00000000378c0000 - 0000000037fef75d to 00881000 - 00fb075d
[    0.000000] ACPI: RSDP 000F7D50, 0024 (r2 DELL  )
[    0.000000] ACPI: XSDT 3F6BB403, 0074 (r1 DELL    M09      6040000  LTP        0)
[    0.000000] ACPI: FACP 3F6BFBCA, 00F4 (r3 INTEL  POULSBO   6040000 INTC       32)
[    0.000000] ACPI: DSDT 3F6BC330, 3826 (r1 INTEL   POULSBO  6040000 INTL 20060608)
[    0.000000] ACPI: FACS 3F6C2FC0, 0040
[    0.000000] ACPI: HPET 3F6BFCBE, 0038 (r1 INTEL  POULSBO   6040000 INTC       32)
[    0.000000] ACPI: MCFG 3F6BFCF6, 003C (r1 INTEL  POULSBO   6040000 INTC       32)
[    0.000000] ACPI: TCPA 3F6BFD32, 0032 (r1 PTLTD  CALISTGA  6040000  PTL        1)
[    0.000000] ACPI: TMOR 3F6BFD64, 0026 (r1 PTLTD            6040000 PTL         3)
[    0.000000] ACPI: OSFR 3F6BFD8A, 0070 (r1 DELL   DELL      6040000 ASL        61)
[    0.000000] ACPI: APIC 3F6BFDFA, 0068 (r1 PTLTD  	 APIC    6040000  LTP        0)
[    0.000000] ACPI: BOOT 3F6BFE62, 0028 (r1 PTLTD  $SBFTBL$  6040000  LTP        1)
[    0.000000] ACPI: SLIC 3F6BFE8A, 0176 (r1 DELL    M09      6040000  LTP        0)
[    0.000000] ACPI: SSDT 3F6BB477, 04DC (r2  PmRef    CpuPm     3000 INTL 20050624)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 130MB HIGHMEM available.
[    0.000000] 883MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 373fe000
[    0.000000]   low ram: 00000000 - 373fe000
[    0.000000]   bootmap 00012000 - 00018e80
[    0.000000] (9 early reservations) ==> bootmem [0000000000 - 00373fe000]
[    0.000000]   #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
[    0.000000]   #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
[    0.000000]   #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
[    0.000000]   #3 [0000100000 - 000087c52c]    TEXT DATA BSS ==> [0000100000 - 000087c52c]
[    0.000000]   #4 [000087d000 - 0000881000]    INIT_PG_TABLE ==> [000087d000 - 0000881000]
[    0.000000]   #5 [0000097000 - 0000100000]    BIOS reserved ==> [0000097000 - 0000100000]
[    0.000000]   #6 [0000010000 - 0000012000]          PGTABLE ==> [0000010000 - 0000012000]
[    0.000000]   #7 [0000881000 - 0000fb075e]      NEW RAMDISK ==> [0000881000 - 0000fb075e]
[    0.000000]   #8 [0000012000 - 0000019000]          BOOTMAP ==> [0000012000 - 0000019000]
[    0.000000] found SMP MP-table at [c00f7de0] 000f7de0
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000000 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000373fe
[    0.000000]   HighMem  0x000373fe -> 0x0003f6b0
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[4] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00000002
[    0.000000]     0: 0x00000006 -> 0x00000007
[    0.000000]     0: 0x00000010 -> 0x0000008a
[    0.000000]     0: 0x00000100 -> 0x0003f6b0
[    0.000000] On node 0 totalpages: 259629
[    0.000000] free_area_init_node: node 0, pgdat c06d0f80, node_mem_map c1000000
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3933 pages, LIFO batch:0
[    0.000000]   Normal zone: 1736 pages used for memmap
[    0.000000]   Normal zone: 220470 pages, LIFO batch:31
[    0.000000]   HighMem zone: 262 pages used for memmap
[    0.000000]   HighMem zone: 33196 pages, LIFO batch:7
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] ACPI: PM-Timer IO Port: 0x1008
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000
[    0.000000] PM: Registered nosave memory: 0000000000007000 - 0000000000010000
[    0.000000] PM: Registered nosave memory: 000000000008a000 - 0000000000097000
[    0.000000] PM: Registered nosave memory: 0000000000097000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[    0.000000] PM: Registered nosave memory: 00000000000d0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[    0.000000] PERCPU: Allocating 45056 bytes of per cpu data
[    0.000000] NR_CPUS: 64, nr_cpu_ids: 2, nr_node_ids 1
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257599
[    0.000000] Kernel command line: root=UUID=e838fa66-e010-411c-827e-34c17a629bb6 ro quiet splash 
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Extended CMOS year: 2000
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 1596.049 MHz processor.
[    0.004000] Console: colour VGA+ 80x25
[    0.004000] console [tty0] enabled
[    0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.004000] allocated 5195200 bytes of page_cgroup
[    0.004000] please try cgroup_disable=memory option if you don't want
[    0.004000] Scanning for low memory corruption every 60 seconds
[    0.004000] Memory: 1008944k/1039040k available (4126k kernel code, 29184k reserved, 2208k data, 532k init, 133832k highmem)
[    0.004000] virtual kernel memory layout:
[    0.004000]     fixmap  : 0xffc77000 - 0xfffff000   (3616 kB)
[    0.004000]     pkmap   : 0xff400000 - 0xff800000   (4096 kB)
[    0.004000]     vmalloc : 0xf7bfe000 - 0xff3fe000   ( 120 MB)
[    0.004000]     lowmem  : 0xc0000000 - 0xf73fe000   ( 883 MB)
[    0.004000]       .init : 0xc0737000 - 0xc07bc000   ( 532 kB)
[    0.004000]       .data : 0xc0507a6f - 0xc072fe60   (2208 kB)
[    0.004000]       .text : 0xc0100000 - 0xc0507a6f   (4126 kB)
[    0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.004000] hpet clockevent registered
[    0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 3192.09 BogoMIPS (lpj=6384196)
[    0.004000] Security Framework initialized
[    0.004000] SELinux:  Disabled at boot.
[    0.004000] AppArmor: AppArmor initialized
[    0.004000] Mount-cache hash table entries: 512
[    0.004000] Initializing cgroup subsys ns
[    0.004000] Initializing cgroup subsys cpuacct
[    0.004000] Initializing cgroup subsys memory
[    0.004000] Initializing cgroup subsys freezer
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.004000] CPU: L2 cache: 512K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 0
[    0.004000] using mwait in idle threads.
[    0.004000] Checking 'hlt' instruction... OK.
[    0.019926] ACPI: Core revision 20080926
[    0.021494] ACPI: Checking initramfs for custom DSDT
[    0.491582] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.531283] CPU0: Intel(R) Atom(TM) CPU Z530   @ 1.60GHz stepping 02
[    0.532002] Booting processor 1 APIC 0x1 ip 0x6000
[    0.004000] Initializing CPU#1
[    0.004000] Calibrating delay using timer specific routine.. 3191.93 BogoMIPS (lpj=6383870)
[    0.004000] CPU: L1 I cache: 32K, L1 D cache: 24K
[    0.004000] CPU: L2 cache: 512K
[    0.004000] CPU: Physical Processor ID: 0
[    0.004000] CPU: Processor Core ID: 0
[    0.616245] CPU1: Intel(R) Atom(TM) CPU Z530   @ 1.60GHz stepping 02
[    0.616283] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.620072] Brought up 2 CPUs
[    0.620079] Total of 2 processors activated (6384.03 BogoMIPS).
[    0.620148] CPU0 attaching sched-domain:
[    0.620153]  domain 0: span 0-1 level SIBLING
[    0.620159]   groups: 0 1
[    0.620169] CPU1 attaching sched-domain:
[    0.620173]  domain 0: span 0-1 level SIBLING
[    0.620178]   groups: 1 0
[    0.620320] net_namespace: 776 bytes
[    0.620320] Booting paravirtualized kernel on bare hardware
[    0.620706] Time: 22:42:12  Date: 02/26/10
[    0.620706] regulator: core version 0.5
[    0.620706] NET: Registered protocol family 16
[    0.620706] EISA bus registered
[    0.620706] ACPI: bus type pci registered
[    0.620706] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[    0.620706] PCI: MCFG area at e0000000 reserved in E820
[    0.620706] PCI: Using MMCONFIG for extended config space
[    0.620706] PCI: Using configuration type 1 for base access
[    0.625257] ACPI: EC: Look up EC in DSDT
[    0.629400] ACPI: BIOS _OSI(Linux) query ignored
[    0.630409] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.632251] ACPI: Interpreter enabled
[    0.632267] ACPI: (supports S0 S3 S4 S5)
[    0.632338] ACPI: Using IOAPIC for interrupt routing
[    0.680886] ACPI: EC: GPE = 0xd, I/O: command/status = 0x66, data = 0x62
[    0.680892] ACPI: EC: driver started in interrupt mode
[    0.681154] ACPI: No dock devices found.
[    0.681174] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.681330] pci 0000:00:02.0: reg 10 32bit mmio: [0xd8100000-0xd817ffff]
[    0.681341] pci 0000:00:02.0: reg 14 io port: [0x1800-0x1807]
[    0.681351] pci 0000:00:02.0: reg 18 32bit mmio: [0xd0000000-0xd7ffffff]
[    0.681361] pci 0000:00:02.0: reg 1c 32bit mmio: [0xd8380000-0xd839ffff]
[    0.681457] pci 0000:00:1b.0: reg 10 64bit mmio: [0xd83a0000-0xd83a3fff]
[    0.681494] pci 0000:00:1b.0: PME# supported from D0 D3hot
[    0.681500] pci 0000:00:1b.0: PME# disabled
[    0.681552] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[    0.681559] pci 0000:00:1c.0: PME# disabled
[    0.681613] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[    0.681619] pci 0000:00:1c.1: PME# disabled
[    0.681673] pci 0000:00:1d.0: reg 20 io port: [0x1820-0x183f]
[    0.681726] pci 0000:00:1d.1: reg 20 io port: [0x1840-0x185f]
[    0.681779] pci 0000:00:1d.2: reg 20 io port: [0x1860-0x187f]
[    0.681852] pci 0000:00:1d.7: reg 10 32bit mmio: [0xd83a4000-0xd83a43ff]
[    0.681909] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.681918] pci 0000:00:1d.7: PME# disabled
[    0.682018] pci 0000:00:1f.1: reg 20 io port: [0x1810-0x181f]
[    0.682097] pci 0000:02:00.0: reg 10 io port: [0x2000-0x20ff]
[    0.682123] pci 0000:02:00.0: reg 18 64bit mmio: [0xd8410000-0xd8410fff]
[    0.682142] pci 0000:02:00.0: reg 20 64bit mmio: [0xd8400000-0xd840ffff]
[    0.682155] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x01ffff]
[    0.682171] pci 0000:02:00.0: supports D1 D2
[    0.682175] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.682183] pci 0000:02:00.0: PME# disabled
[    0.682249] pci 0000:00:1c.0: bridge io port: [0x2000-0x2fff]
[    0.682259] pci 0000:00:1c.0: bridge 32bit mmio pref: [0xd8400000-0xd84fffff]
[    0.682330] pci 0000:03:00.0: reg 10 64bit mmio: [0xd8000000-0xd8003fff]
[    0.682381] pci 0000:03:00.0: supports D1 D2
[    0.682385] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    0.682393] pci 0000:03:00.0: PME# disabled
[    0.682460] pci 0000:00:1c.1: bridge 32bit mmio: [0xd8000000-0xd80fffff]
[    0.682479] bus 00 -> node 0
[    0.682491] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.682996] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.683256] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.690997] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 5 6 *7 10 12 14 15)
[    0.691216] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 5 6 7 *11 12 14 15)
[    0.691431] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 5 6 7 10 12 14 15)
[    0.691645] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 *5 6 7 11 12 14 15)
[    0.691859] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 5 6 7 10 12 14 15) *0, disabled.
[    0.692095] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 5 6 7 *11 12 14 15)
[    0.692310] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 5 6 7 *10 12 14 15)
[    0.692531] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 5 6 7 11 12 14 15) *10
[    0.692911] ACPI: WMI: Mapper loaded
[    0.693036] SCSI subsystem initialized
[    0.693036] libata version 3.00 loaded.
[    0.693036] usbcore: registered new interface driver usbfs
[    0.693036] usbcore: registered new interface driver hub
[    0.693036] usbcore: registered new device driver usb
[    0.693036] PCI: Using ACPI for IRQ routing
[    0.700040] Bluetooth: Core ver 2.13
[    0.700109] NET: Registered protocol family 31
[    0.700109] Bluetooth: HCI device and connection manager initialized
[    0.700109] Bluetooth: HCI socket layer initialized
[    0.700109] NET: Registered protocol family 8
[    0.700109] NET: Registered protocol family 20
[    0.700145] NetLabel: Initializing
[    0.700153] NetLabel:  domain hash size = 128
[    0.700162] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.700204] NetLabel:  unlabeled traffic allowed by default
[    0.700240] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.700250] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.704120] AppArmor: AppArmor Filesystem Enabled
[    0.708027] Switched to high resolution mode on CPU 0
[    0.708373] Switched to high resolution mode on CPU 1
[    0.712090] pnp: PnP ACPI init
[    0.712131] ACPI: bus type pnp registered
[    0.732513] pnp: PnP ACPI: found 10 devices
[    0.732518] ACPI: ACPI bus type pnp unregistered
[    0.732525] PnPBIOS: Disabled by ACPI PNP
[    0.732546] system 00:01: iomem range 0xfd000000-0xfd003fff has been reserved
[    0.732553] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[    0.732559] system 00:01: iomem range 0xfed00000-0xfed3ffff could not be reserved
[    0.732566] system 00:01: iomem range 0xfed40000-0xfed44fff has been reserved
[    0.732572] system 00:01: iomem range 0xfed45000-0xfed4bfff has been reserved
[    0.732586] system 00:04: iomem range 0xfed00000-0xfed003ff has been reserved
[    0.732600] system 00:06: ioport range 0x680-0x69f has been reserved
[    0.732606] system 00:06: ioport range 0x8080-0x8080 has been reserved
[    0.732612] system 00:06: ioport range 0x1000-0x107f has been reserved
[    0.732618] system 00:06: ioport range 0x1180-0x11bf has been reserved
[    0.732624] system 00:06: ioport range 0x1640-0x164f has been reserved
[    0.732630] system 00:06: ioport range 0x374-0x375 has been reserved
[    0.732636] system 00:06: ioport range 0x3f4-0x3f5 has been reserved
[    0.767520] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.767528] pci 0000:00:1c.0:   IO window: 0x2000-0x2fff
[    0.767537] pci 0000:00:1c.0:   MEM window: 0x50000000-0x500fffff
[    0.767545] pci 0000:00:1c.0:   PREFETCH window: 0x000000d8400000-0x000000d84fffff
[    0.767555] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[    0.767559] pci 0000:00:1c.1:   IO window: disabled
[    0.767567] pci 0000:00:1c.1:   MEM window: 0xd8000000-0xd80fffff
[    0.767573] pci 0000:00:1c.1:   PREFETCH window: disabled
[    0.767598] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.767607] pci 0000:00:1c.0: setting latency timer to 64
[    0.767621] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[    0.767628] pci 0000:00:1c.1: setting latency timer to 64
[    0.767635] bus: 00 index 0 io port: [0x00-0xffff]
[    0.767640] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.767645] bus: 02 index 0 io port: [0x2000-0x2fff]
[    0.767649] bus: 02 index 1 mmio: [0x50000000-0x500fffff]
[    0.767654] bus: 02 index 2 mmio: [0xd8400000-0xd84fffff]
[    0.767659] bus: 02 index 3 mmio: [0x0-0x0]
[    0.767663] bus: 03 index 0 mmio: [0x0-0x0]
[    0.767667] bus: 03 index 1 mmio: [0xd8000000-0xd80fffff]
[    0.767672] bus: 03 index 2 mmio: [0x0-0x0]
[    0.767676] bus: 03 index 3 mmio: [0x0-0x0]
[    0.767698] NET: Registered protocol family 2
[    0.780284] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.780883] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.782108] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.782859] TCP: Hash tables configured (established 131072 bind 65536)
[    0.782867] TCP reno registered
[    0.788364] NET: Registered protocol family 1
[    0.788622] checking if image is initramfs... it is
[    1.766229] Freeing initrd memory: 7357k freed
[    1.766309] Simple Boot Flag at 0x36 set to 0x1
[    1.766707] cpufreq: No nForce2 chipset.
[    1.766987] audit: initializing netlink socket (disabled)
[    1.767032] type=2000 audit(1267224132.764:1): initialized
[    1.781526] highmem bounce pool size: 64 pages
[    1.781538] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.784352] VFS: Disk quotas dquot_6.5.1
[    1.784477] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.785822] fuse init (API version 7.10)
[    1.786006] msgmni has been set to 1724
[    1.786369] alg: No test for stdrng (krng)
[    1.786402] io scheduler noop registered
[    1.786407] io scheduler anticipatory registered
[    1.786411] io scheduler deadline registered
[    1.786452] io scheduler cfq registered (default)
[    1.786480] pci 0000:00:02.0: Boot video device
[    1.828442] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.828487] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.828521] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.828596] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    1.828636] pci_express 0000:00:1c.1:pcie00: allocate port service
[    1.828663] pci_express 0000:00:1c.1:pcie02: allocate port service
[    1.828760] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.829082] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.830091] ACPI: AC Adapter [ACAD] (off-line)
[    1.954296] ACPI: Battery Slot [BAT1] (battery present)
[    1.954351] ACPI Error (evxfevnt-0186): Could not enable PowerButton event [20080926]
[    1.954361] ACPI Warning (evxface-0145): Could not enable fixed event 2 [20080926]
[    1.954472] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0
[    1.954549] ACPI: Lid Switch [LID0]
[    1.954648] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    1.954660] ACPI: Power Button (CM) [PWRB]
[    1.955645] ACPI: SSDT 3F6BC017, 0245 (r2  PmRef  Cpu0Ist     3000 INTL 20050624)
[    1.956314] ACPI: SSDT 3F6BB953, 063F (r2  PmRef  Cpu0Cst     3001 INTL 20050624)
[    1.957222] Monitor-Mwait will be used to enter C-1 state
[    1.957229] Monitor-Mwait will be used to enter C-2 state
[    1.957235] Monitor-Mwait will be used to enter C-3 state
[    1.957240] Monitor-Mwait will be used to enter C-3 state
[    1.957273] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[    1.957329] processor ACPI_CPU:00: registered as cooling_device0
[    1.957338] ACPI: Processor [CPU0] (supports 8 throttling states)
[    1.957985] ACPI: SSDT 3F6BC25C, 00D4 (r2  PmRef  Cpu1Ist     3000 INTL 20050624)
[    1.958533] ACPI: SSDT 3F6BBF92, 0085 (r2  PmRef  Cpu1Cst     3000 INTL 20050624)
[    1.959805] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
[    1.959868] processor ACPI_CPU:01: registered as cooling_device1
[    1.959881] ACPI: Processor [CPU1] (supports 8 throttling states)
[    1.980538] isapnp: Scanning for PnP cards...
[    2.334653] isapnp: No Plug & Play device found
[    2.337833] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    2.339714] brd: module loaded
[    2.340433] loop: module loaded
[    2.340588] Fixed MDIO Bus: probed
[    2.340601] PPP generic driver version 2.4.2
[    2.340750] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    2.340819] Driver 'sd' needs updating - please use bus_type methods
[    2.340839] Driver 'sr' needs updating - please use bus_type methods
[    2.342103] pata_sch 0000:00:1f.1: version 0.2
[    2.342178] pata_sch 0000:00:1f.1: setting latency timer to 64
[    2.342344] scsi0 : pata_sch
[    2.342671] scsi1 : pata_sch
[    2.343403] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[    2.343410] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[    2.505592] ata1.00: ATA-7: SAMSUNG HS04THB, NK100-05, max UDMA/100
[    2.505606] ata1.00: 78140160 sectors, multi 16: LBA 
[    2.512600] ata1.00: configured for UDMA/100
[    2.678884] scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HS04THB  NK10 PQ: 0 ANSI: 5
[    2.679103] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[    2.679146] sd 0:0:0:0: [sda] Write Protect is off
[    2.679152] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.679223] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.679370] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors: (40.0 GB/37.2 GiB)
[    2.679410] sd 0:0:0:0: [sda] Write Protect is off
[    2.679416] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.679485] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.679494]  sda: sda1 sda2 sda3 sda4
[    2.850256] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.850363] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.850604] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.850658] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 21 (level, low) -> IRQ 21
[    2.850706] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    2.850714] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    2.850835] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    2.854750] ehci_hcd 0000:00:1d.7: debug port 1
[    2.854762] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    2.854790] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xd83a4000
[    2.868070] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    2.868339] usb usb1: configuration #1 chosen from 1 choice
[    2.868437] hub 1-0:1.0: USB hub found
[    2.868453] hub 1-0:1.0: 8 ports detected
[    2.868689] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.868734] uhci_hcd: USB Universal Host Controller Interface driver
[    2.868812] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    2.868825] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    2.868830] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    2.868923] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    2.868963] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[    2.869119] usb usb2: configuration #1 chosen from 1 choice
[    2.869174] hub 2-0:1.0: USB hub found
[    2.869189] hub 2-0:1.0: 2 ports detected
[    2.869353] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    2.869369] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    2.869375] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    2.869476] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    2.869516] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[    2.869674] usb usb3: configuration #1 chosen from 1 choice
[    2.869728] hub 3-0:1.0: USB hub found
[    2.869742] hub 3-0:1.0: 2 ports detected
[    2.869904] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    2.869914] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    2.869920] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    2.870003] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    2.870042] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[    2.870190] usb usb4: configuration #1 chosen from 1 choice
[    2.870249] hub 4-0:1.0: USB hub found
[    2.870263] hub 4-0:1.0: 2 ports detected
[    2.870506] usbcore: registered new interface driver libusual
[    2.870572] usbcore: registered new interface driver usbserial
[    2.870595] USB Serial support registered for generic
[    2.870630] usbcore: registered new interface driver usbserial_generic
[    2.870634] usbserial: USB Serial Driver core
[    2.870715] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[    2.898121] serio: i8042 KBD port at 0x60,0x64 irq 1
[    2.898135] serio: i8042 AUX port at 0x60,0x64 irq 12
[    2.900178] mice: PS/2 mouse device common for all mice
[    2.912277] rtc_cmos 00:07: RTC can wake from S4
[    2.912402] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[    2.912448] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[    2.912594] device-mapper: uevent: version 1.0.3
[    2.912811] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel redhat com
[    2.912991] device-mapper: multipath: version 1.0.5 loaded
[    2.912997] device-mapper: multipath round-robin: version 1.0.0 loaded
[    2.913207] EISA: Probing bus 0 at eisa.0
[    2.913220] Cannot allocate resource for EISA slot 1
[    2.913226] Cannot allocate resource for EISA slot 2
[    2.913256] Cannot allocate resource for EISA slot 8
[    2.913261] EISA: Detected 0 cards.
[    2.913558] cpuidle: using governor ladder
[    2.913844] cpuidle: using governor menu
[    2.914941] TCP cubic registered
[    2.915169] NET: Registered protocol family 10
[    2.916043] lo: Disabled Privacy Extensions
[    2.916762] NET: Registered protocol family 17
[    2.916807] Bluetooth: L2CAP ver 2.11
[    2.916811] Bluetooth: L2CAP socket layer initialized
[    2.916817] Bluetooth: SCO (Voice Link) ver 0.6
[    2.916820] Bluetooth: SCO socket layer initialized
[    2.916907] Bluetooth: RFCOMM socket layer initialized
[    2.916923] Bluetooth: RFCOMM TTY layer initialized
[    2.916926] Bluetooth: RFCOMM ver 1.10
[    2.916999] Marking TSC unstable due to TSC halts in idle
[    2.918207] Using IPI No-Shortcut mode
[    2.918405] registered taskstats version 1
[    2.918596]   Magic number: 14:946:755
[    2.918710] rtc_cmos 00:07: setting system clock to 2010-02-26 22:42:14 UTC (1267224134)
[    2.918719] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    2.918723] EDD information not available.
[    2.919166] Freeing unused kernel memory: 532k freed
[    2.919477] Write protecting the kernel text: 4128k
[    2.919584] Write protecting the kernel read-only data: 1532k
[    2.931031] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    3.307208] usb 1-6: new high speed USB device using ehci_hcd and address 3
[    3.451611] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    3.451655] r8169 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    3.451689] r8169 0000:02:00.0: setting latency timer to 64
[    3.451847] r8169 0000:02:00.0: irq 2303 for MSI/MSI-X
[    3.454533] eth0: RTL8102e at 0xf7c68000, 00:24:e8:b2:f0:28, XID 24a00000 IRQ 2303
[    3.483679] usb 1-6: configuration #1 chosen from 1 choice
[    3.600076] usb 1-7: new high speed USB device using ehci_hcd and address 4
[    3.751552] usb 1-7: configuration #1 chosen from 1 choice
[    3.818456] Initializing USB Mass Storage driver...
[    3.861111] scsi2 : SCSI emulation for USB Mass Storage devices
[    3.887265] usbcore: registered new interface driver usb-storage
[    3.887278] USB Mass Storage support registered.
[    3.887534] usb-storage: device found at 4
[    3.887540] usb-storage: waiting for device to settle before scanning
[    4.012076] usb 3-1: new full speed USB device using uhci_hcd and address 2
[    4.195267] usb 3-1: configuration #1 chosen from 1 choice
[    4.612637] kjournald starting.  Commit interval 5 seconds
[    4.612689] EXT3-fs: mounted filesystem with ordered data mode.
[    5.000252] Clocksource tsc unstable (delta = -266038903 ns)
[    8.885112] usb-storage: device scan complete
[    8.887791] scsi 2:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS
[    8.890992] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[    8.891135] sd 2:0:0:0: Attached scsi generic sg1 type 0
[   12.694233] udev: starting version 141
[   12.986716] ieee80211_crypt: registered algorithm 'NULL'
[   12.998024] wl: module license '' taints kernel.
[   13.005214] wl 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[   13.005236] wl 0000:03:00.0: setting latency timer to 64
[   13.065183] ieee80211_crypt: registered algorithm 'TKIP'
[   13.065567] eth1: Broadcom BCM4315 802.11 Wireless Controller 5.10.79.10
[   13.177183] Linux video capture interface: v2.00
[   13.237904] acpi device:06: registered as cooling_device2
[   13.292154] acpi device:07: registered as cooling_device3
[   13.292521] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/input/input4
[   13.332398] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   13.853906] Bluetooth: Generic Bluetooth USB driver ver 0.3
[   13.854230] usbcore: registered new interface driver btusb
[   14.101946] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2)
[   14.163918] input: PC Speaker as /devices/platform/pcspkr/input/input5
[   14.225412] uvcvideo: Found UVC 1.00 device Integrated Webcam (064e:a118)
[   14.227069] input: Integrated Webcam as /devices/pci0000:00/0000:00:1d.7/usb1/1-6/1-6:1.0/input/input6
[   14.232403] usbcore: registered new interface driver uvcvideo
[   14.232473] USB Video Class driver (v0.1.0)
[   14.244890] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[   14.578890] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   14.579144] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   14.610112] hda_codec: Unknown model for ALC269, trying auto-probe from BIOS...
[   14.966197] lp: driver loaded but no devices found
[   15.185653] EXT3 FS on sda4, internal journal
[   15.335370] Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000
[   15.419599] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input7
[   18.309543] Adding 1048568k swap on /mnt/1024Mb.swap.  Priority:-1 extents:271 across:1070916k
[   18.824843] type=1505 audit(1267224150.405:2): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1895
[   18.825229] type=1505 audit(1267224150.405:3): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1895
[   18.825350] type=1505 audit(1267224150.405:4): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1895
[   18.825450] type=1505 audit(1267224150.405:5): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1895
[   19.149252] type=1505 audit(1267224150.729:6): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=1900
[   19.149739] type=1505 audit(1267224150.729:7): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=1900
[   19.216158] type=1505 audit(1267224150.797:8): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=1904
[   23.184801] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   23.184810] Bluetooth: BNEP filters: protocol multicast
[   23.222800] Bridge firewalling registered
[   24.879501] ppdev: user-space parallel port driver
[   28.420048] r8169: eth0: link down
[   28.420594] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   32.119889] hda-intel: Invalid position buffer, using LPIB read method instead.
[   32.119940] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[   33.293217] eth1: no IPv6 routers present
[  130.852310] hub 1-0:1.0: unable to enumerate USB device on port 1
[  131.800343] usb 2-1: new full speed USB device using uhci_hcd and address 2
[  131.960661] usb 2-1: configuration #1 chosen from 1 choice
[  131.995209] usb-storage: probe of 2-1:1.0 failed with error -5
[  131.995964] usb 2-1: USB disconnect, address 2
[  133.568339] usb 2-1: new full speed USB device using uhci_hcd and address 3
[  133.729611] usb 2-1: configuration #1 chosen from 1 choice
[  133.747981] scsi4 : SCSI emulation for USB Mass Storage devices
[  133.757131] usb-storage: device found at 3
[  133.757145] usb-storage: waiting for device to settle before scanning
[  134.051043] USB Serial support registered for Sierra USB modem
[  134.051181] sierra 2-1:1.0: Sierra USB modem converter detected
[  134.054611] usb 2-1: Sierra USB modem converter now attached to ttyUSB0
[  134.054878] usb 2-1: Sierra USB modem converter now attached to ttyUSB1
[  134.055128] usb 2-1: Sierra USB modem converter now attached to ttyUSB2
[  134.055405] usb 2-1: Sierra USB modem converter now attached to ttyUSB3
[  134.055503] usbcore: registered new interface driver sierra
[  134.055518] sierra: v.1.3.2:USB Driver for Sierra Wireless USB modems
[  138.758552] usb-storage: device scan complete
[  138.761264] scsi 4:0:0:0: Direct-Access     Sierra   Wireless Storage 2.31 PQ: 0 ANSI: 2
[  138.774790] sd 4:0:0:0: [sdc] Attached SCSI removable disk
[  138.780684] sd 4:0:0:0: Attached scsi generic sg2 type 0
[  275.575811] PPP BSD Compression module registered
[  275.636169] PPP Deflate Compression module registered
[  574.537249] usb 2-1: USB disconnect, address 3
[  574.538930] sierra ttyUSB0: Sierra USB modem converter now disconnected from ttyUSB0
[  574.539137] sierra ttyUSB1: Sierra USB modem converter now disconnected from ttyUSB1
[  574.539313] sierra ttyUSB2: Sierra USB modem converter now disconnected from ttyUSB2
[  574.539491] sierra ttyUSB3: Sierra USB modem converter now disconnected from ttyUSB3
[  574.539747] sierra 2-1:1.0: device disconnected
[ 1696.448325] hub 1-0:1.0: unable to enumerate USB device on port 2
[ 1697.396285] usb 2-2: new full speed USB device using uhci_hcd and address 4
[ 1697.551065] usb 2-2: configuration #1 chosen from 1 choice
[ 1697.585615] usb-storage: probe of 2-2:1.0 failed with error -5
[ 1697.728361] usb 2-2: USB disconnect, address 4
[ 1699.208299] usb 2-2: new full speed USB device using uhci_hcd and address 5
[ 1699.364161] usb 2-2: configuration #1 chosen from 1 choice
[ 1699.366761] sierra 2-2:1.0: Sierra USB modem converter detected
[ 1699.370137] usb 2-2: Sierra USB modem converter now attached to ttyUSB0
[ 1699.370462] usb 2-2: Sierra USB modem converter now attached to ttyUSB1
[ 1699.370771] usb 2-2: Sierra USB modem converter now attached to ttyUSB2
[ 1699.371047] usb 2-2: Sierra USB modem converter now attached to ttyUSB3
[ 1699.437170] scsi6 : SCSI emulation for USB Mass Storage devices
[ 1699.438311] usb-storage: device found at 5
[ 1699.438324] usb-storage: waiting for device to settle before scanning
[ 1704.439027] usb-storage: device scan complete
[ 1704.442868] scsi 6:0:0:0: Direct-Access     Sierra   Wireless Storage 2.31 PQ: 0 ANSI: 2
[ 1704.452983] sd 6:0:0:0: [sdc] Attached SCSI removable disk
[ 1704.454611] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 1772.376359] usb 2-2: USB disconnect, address 5
[ 1772.378950] sierra ttyUSB0: Sierra USB modem converter now disconnected from ttyUSB0
[ 1772.379357] sierra ttyUSB1: Sierra USB modem converter now disconnected from ttyUSB1
[ 1772.379675] sierra ttyUSB2: Sierra USB modem converter now disconnected from ttyUSB2
[ 1772.379994] sierra ttyUSB3: Sierra USB modem converter now disconnected from ttyUSB3
[ 1772.385785] sierra 2-2:1.0: device disconnected
[ 3333.116705] r8169: eth0: link down
[ 3333.117742] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3333.377316] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 3334.304398] usb 2-1: new full speed USB device using uhci_hcd and address 6
[ 3334.460334] usb 2-1: configuration #1 chosen from 1 choice
[ 3334.494815] usb-storage: probe of 2-1:1.0 failed with error -5
[ 3334.528175] usb 2-1: USB disconnect, address 6
[ 3336.008357] usb 2-1: new full speed USB device using uhci_hcd and address 7
[ 3336.164397] usb 2-1: configuration #1 chosen from 1 choice
[ 3336.166975] sierra 2-1:1.0: Sierra USB modem converter detected
[ 3336.170149] usb 2-1: Sierra USB modem converter now attached to ttyUSB0
[ 3336.170402] usb 2-1: Sierra USB modem converter now attached to ttyUSB1
[ 3336.170670] usb 2-1: Sierra USB modem converter now attached to ttyUSB2
[ 3336.170923] usb 2-1: Sierra USB modem converter now attached to ttyUSB3
[ 3336.255459] scsi8 : SCSI emulation for USB Mass Storage devices
[ 3336.295568] usb-storage: device found at 7
[ 3336.295576] usb-storage: waiting for device to settle before scanning
[ 3338.112212] eth1: no IPv6 routers present
[ 3383.065256] usb-storage: device scan complete
[ 3383.067850] scsi 8:0:0:0: Direct-Access     Sierra   Wireless Storage 2.31 PQ: 0 ANSI: 2
[ 3383.079670] sd 8:0:0:0: [sdc] Attached SCSI removable disk
[ 3383.080011] sd 8:0:0:0: Attached scsi generic sg2 type 0
[ 3824.824111] usb 2-1: USB disconnect, address 7
[ 3824.825815] sierra ttyUSB0: Sierra USB modem converter now disconnected from ttyUSB0
[ 3824.825963] sierra ttyUSB1: Sierra USB modem converter now disconnected from ttyUSB1
[ 3824.826104] sierra ttyUSB2: Sierra USB modem converter now disconnected from ttyUSB2
[ 3824.826245] sierra ttyUSB3: Sierra USB modem converter now disconnected from ttyUSB3
[ 3824.826277] sierra 2-1:1.0: device disconnected
[ 3837.280333] hub 1-0:1.0: unable to enumerate USB device on port 1
[ 3838.228205] usb 2-1: new full speed USB device using uhci_hcd and address 8
[ 3838.384064] usb 2-1: configuration #1 chosen from 1 choice
[ 3838.424488] usb-storage: probe of 2-1:1.0 failed with error -5
[ 3838.464143] usb 2-1: USB disconnect, address 8
[ 3839.944285] usb 2-1: new full speed USB device using uhci_hcd and address 9
[ 3840.100105] usb 2-1: configuration #1 chosen from 1 choice
[ 3840.102747] sierra 2-1:1.0: Sierra USB modem converter detected
[ 3840.106057] usb 2-1: Sierra USB modem converter now attached to ttyUSB0
[ 3840.106307] usb 2-1: Sierra USB modem converter now attached to ttyUSB1
[ 3840.106575] usb 2-1: Sierra USB modem converter now attached to ttyUSB2
[ 3840.106824] usb 2-1: Sierra USB modem converter now attached to ttyUSB3
[ 3840.205414] scsi10 : SCSI emulation for USB Mass Storage devices
[ 3840.206579] usb-storage: device found at 9
[ 3840.206592] usb-storage: waiting for device to settle before scanning
[ 3851.109075] usb-storage: device scan complete
[ 3851.113803] scsi 10:0:0:0: Direct-Access     Sierra   Wireless Storage 2.31 PQ: 0 ANSI: 2
[ 3851.121856] sd 10:0:0:0: [sdc] Attached SCSI removable disk
[ 3851.122033] sd 10:0:0:0: Attached scsi generic sg2 type 0

Plugin /usr/lib/pppd/2.4.4/nm-pppd-plugin.so loaded.
using channel 2
Using interface ppp0
Connect: ppp0 <--> /dev/ttyUSB0
sent [LCP ConfReq id=0x1 <asyncmap 0x0> <magic 0x3b52486f> <pcomp> <accomp>]
rcvd [LCP ConfReq id=0x0 <asyncmap 0x0> <magic 0x7cf7f6dd> <pcomp> <accomp>]
sent [LCP ConfAck id=0x0 <asyncmap 0x0> <magic 0x7cf7f6dd> <pcomp> <accomp>]
rcvd [LCP ConfAck id=0x1 <asyncmap 0x0> <magic 0x3b52486f> <pcomp> <accomp>]
sent [CCP ConfReq id=0x1 <deflate 15> <deflate(old#) 15> <bsd v1 15>]
sent [IPCP ConfReq id=0x1 <compress VJ 0f 01> <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
rcvd [LCP DiscReq id=0x1 magic=0x7cf7f6dd]
rcvd [IPCP ConfReq id=0x0 <addr 206.47.201.2>]
sent [IPCP ConfAck id=0x0 <addr 206.47.201.2>]
rcvd [LCP ProtRej id=0x2 80 fd 01 01 00 0f 1a 04 78 00 18 04 78 00 15 03 2f]
Protocol-Reject for 'Compression Control Protocol' (0x80fd) received
rcvd [IPCP ConfRej id=0x1 <compress VJ 0f 01>]
sent [IPCP ConfReq id=0x2 <addr 0.0.0.0> <ms-dns1 0.0.0.0> <ms-dns2 0.0.0.0>]
rcvd [IPCP ConfNak id=0x2 <addr 10.73.15.236> <ms-dns1 206.47.201.246> <ms-dns2 204.101.237.136>]
sent [IPCP ConfReq id=0x3 <addr 10.73.15.236> <ms-dns1 206.47.201.246> <ms-dns2 204.101.237.136>]
rcvd [IPCP ConfNak id=0x3]
sent [IPCP ConfReq id=0x4 <addr 10.73.15.236> <ms-dns1 206.47.201.246> <ms-dns2 204.101.237.136>]
rcvd [IPCP ConfNak id=0x4]
sent [IPCP ConfReq id=0x5 <addr 10.73.15.236> <ms-dns1 206.47.201.246> <ms-dns2 204.101.237.136>]
rcvd [IPCP ConfAck id=0x5 <addr 10.73.15.236> <ms-dns1 206.47.201.246> <ms-dns2 204.101.237.136>]
Cannot determine ethernet address for proxy ARP
local  IP address 10.73.15.236
remote IP address 206.47.201.2
primary   DNS address 206.47.201.246
secondary DNS address 204.101.237.136
Script /etc/ppp/ip-up started (pid 6800)
Script /etc/ppp/ip-up finished (pid 6800), status = 0x0
Terminating on signal 15
Connect time 5.7 minutes.
Sent 314 bytes, received 544 bytes.
Script /etc/ppp/ip-down started (pid 6952)
sent [LCP TermReq id=0x2 "User request"]
rcvd [LCP TermAck id=0x2]
Connection terminated.
Script /etc/ppp/ip-down finished (pid 6952), status = 0x0

s Ne*
NetworkManager
anna dell10:/etc/init.d$ ls -lag Ne*
-rwxr-xr-x 1 root 1822 2009-04-14 08:33 NetworkManager
anna dell10:/etc/init.d$ cd
anna dell10:~$ sudo /etc/init.d/NetworkManager stop
 * Stopping network connection manager NetworkManager                       [ OK ] 
anna dell10:~$ NM_SERIAL_DEBUG=1 NM_PPP_DEBUG=1 /usr/sbin/NetworkManager --no-daemon
You must be root to run NetworkManager!
anna dell10:~$ sudo NM_SERIAL_DEBUG=1 NM_PPP_DEBUG=1 /usr/sbin/NetworkManager --no-daemon > 904_nm_debug.txt
NetworkManager: <info>  starting...
NetworkManager: <info>  Found radio killswitch /org/freedesktop/Hal/devices/dell_wlan_switch
NetworkManager: <info>  (eth0): new Ethernet device (driver: 'r8169')
NetworkManager: <info>  (eth0): exported as /org/freedesktop/Hal/devices/net_00_24_e8_b2_f0_28
NetworkManager: <info>  (eth1): driver does not support SSID scans (scan_capa 0x00).
NetworkManager: <info>  (eth1): new 802.11 WiFi device (driver: 'wl')
NetworkManager: <info>  (eth1): exported as /org/freedesktop/Hal/devices/net_00_23_08_82_f1_5c
NetworkManager: <info>  (eth0): device state change: 1 -> 2
NetworkManager: <info>  (eth0): bringing up device.
NetworkManager: <info>  (eth0): preparing device.
NetworkManager: <info>  (eth0): deactivating device (reason: 2).
NetworkManager: <info>  Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889)
NetworkManager: <info>  Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889)
NetworkManager: <info>  (eth1): device state change: 1 -> 2
NetworkManager: <info>  (eth1): preparing device.
NetworkManager: <info>  (eth1): deactivating device (reason: 2).
NetworkManager: <WARN>  nm_device_wifi_disable_encryption(): error setting key for device eth1: Invalid argument
NetworkManager: <info>  (eth1): device state change: 2 -> 3
NetworkManager: <info>  (eth1): supplicant interface state:  starting -> ready
NetworkManager: <info>  (ttyUSB0): found serial port (udev:CDMA  hal:)
NetworkManager: <info>  (ttyUSB0): deferring until all ports found
NetworkManager: <info>  Re-checking deferred serial ports
NetworkManager: <info>  (ttyUSB0): new Modem device (driver: 'sierra')
NetworkManager: <info>  (ttyUSB0): exported as /org/freedesktop/Hal/devices/usb_device_1199_25__4Vx_________if0_serial_usb_0
NetworkManager: <info>  (ttyUSB0): device state change: 1 -> 2
NetworkManager: <info>  (ttyUSB0): deactivating device (reason: 2).
NetworkManager: nm_system_device_flush_ip4_routes_with_iface: assertion `iface_idx >= 0' failed
NetworkManager: nm_system_device_flush_ip4_addresses_with_iface: assertion `iface_idx >= 0' failed
NetworkManager: <info>  (ttyUSB0): device state change: 2 -> 3
NetworkManager: <info>  Activation (eth1) starting connection 'Auto 2TIVO2'
NetworkManager: <info>  (eth1): device state change: 3 -> 4
NetworkManager: <info>  Activation (eth1) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager: <info>  Activation (eth1) Stage 1 of 5 (Device Prepare) started...
NetworkManager: <info>  Activation (eth1) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager: <info>  Activation (eth1) Stage 1 of 5 (Device Prepare) complete.
NetworkManager: <info>  Activation (eth1) Stage 2 of 5 (Device Configure) starting...
NetworkManager: <info>  (eth1): device state change: 4 -> 5
NetworkManager: <info>  Activation (eth1/wireless): connection 'Auto 2TIVO2' requires no security.  No secrets needed.
NetworkManager: <info>  Config: added 'ssid' value '2TIVO2'
NetworkManager: <info>  Config: added 'scan_ssid' value '1'
NetworkManager: <info>  Config: added 'key_mgmt' value 'NONE'
NetworkManager: <info>  Activation (eth1) Stage 2 of 5 (Device Configure) complete.
NetworkManager: <info>  Config: set interface ap_scan to 1
NetworkManager: <info>  (eth1): supplicant connection state:  scanning -> disconnected
NetworkManager: <info>  (eth1): supplicant connection state:  disconnected -> scanning
NetworkManager: <info>  Activation (ttyUSB0) starting connection 'Auto Mobile Broadband (CDMA) connection'
NetworkManager: <info>  (ttyUSB0): device state change: 3 -> 4
NetworkManager: <info>  Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) scheduled...
NetworkManager: <info>  Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) started...
NetworkManager: <debug> [1267227521.664513] nm_serial_device_open(): (ttyUSB0) opening device...
NetworkManager: <info>  Activation (ttyUSB0) Stage 1 of 5 (Device Prepare) complete.
NetworkManager: <debug> [1267227521.780947] nm_serial_debug(): Sending: 'ATZ E0
'
NetworkManager: <debug> [1267227521.796932] nm_serial_debug(): Got: 'ATZ E0
'
NetworkManager: <debug> [1267227521.824744] nm_serial_debug(): Got: 'ATZ E0


OK

'
NetworkManager: <info>  (ttyUSB0): powering up...
NetworkManager: <debug> [1267227521.825089] nm_serial_debug(): Sending: 'at!pcstate=1
'
NetworkManager: <debug> [1267227521.855205] nm_serial_debug(): Got: '

OK

'
NetworkManager: <debug> [1267227521.855431] nm_serial_debug(): Sending: 'ATDT#777
'
NetworkManager: <debug> [1267227523.179023] nm_serial_debug(): Got: '

CONNECT

'
NetworkManager: <info>  Connected, Woo!
NetworkManager: <info>  Activation (ttyUSB0) Stage 2 of 5 (Device Configure) scheduled...
NetworkManager: <info>  Activation (ttyUSB0) Stage 2 of 5 (Device Configure) starting...
NetworkManager: <info>  (ttyUSB0): device state change: 4 -> 5
NetworkManager: <info>  Starting pppd connection
NetworkManager: <debug> [1267227523.200444] nm_ppp_manager_start(): Command line: /usr/sbin/pppd nodetach lock nodefaultroute debug ttyUSB0 noipdefault noauth usepeerdns lcp-echo-failure 0 lcp-echo-interval 0 ipparam /org/freedesktop/NetworkManager/PPP/0 plugin /usr/lib/pppd/2.4.4/nm-pppd-plugin.so
NetworkManager: <debug> [1267227523.218227] nm_ppp_manager_start(): ppp started with pid 6794
NetworkManager: <info>  Activation (ttyUSB0) Stage 2 of 5 (Device Configure) complete.
NetworkManager: <info>  (ttyUSB0): device state change: 5 -> 6
NetworkManager: <info>  (ttyUSB0): device state change: 6 -> 7
NetworkManager: <info>  PPP manager(IP Config Get) reply received.
NetworkManager: <info>  Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) scheduled...
NetworkManager: <info>  Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) started...
NetworkManager: <info>  Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) scheduled...
NetworkManager: <info>  Activation (ttyUSB0) Stage 4 of 5 (IP Configure Get) complete.
NetworkManager: <info>  Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) started...
NetworkManager: <info>  (ttyUSB0): device state change: 7 -> 8
NetworkManager: <info>  Policy set 'Auto Mobile Broadband (CDMA) connection' (ppp0) as default for routing and DNS.
NetworkManager: <info>  Activation (ttyUSB0) successful, device activated.
NetworkManager: <info>  Activation (ttyUSB0) Stage 5 of 5 (IP Configure Commit) complete.
NetworkManager: <info>  (eth1): supplicant connection state:  scanning -> associating
NetworkManager: <info>  (eth1): supplicant connection state:  associating -> associated
NetworkManager: <info>  (eth1): supplicant connection state:  associated -> completed
NetworkManager: <info>  Activation (eth1/wireless) Stage 2 of 5 (Device Configure) successful.  Connected to wireless network '2TIVO2'.
NetworkManager: <info>  Activation (eth1) Stage 3 of 5 (IP Configure Start) scheduled.
NetworkManager: <info>  Activation (eth1) Stage 3 of 5 (IP Configure Start) started...
NetworkManager: <info>  (eth1): device state change: 5 -> 7
NetworkManager: <info>  Activation (eth1) Beginning DHCP transaction.
NetworkManager: <info>  dhclient started with pid 6816
NetworkManager: <info>  Activation (eth1) Stage 3 of 5 (IP Configure Start) complete.
Internet Systems Consortium DHCP Client V3.1.1
Copyright 2004-2008 Internet Systems Consortium.
All rights reserved.
For info, please visit http://www.isc.org/sw/dhcp/

NetworkManager: <info>  DHCP: device eth1 state changed (null) -> preinit
Listening on LPF/eth1/00:23:08:82:f1:5c
Sending on   LPF/eth1/00:23:08:82:f1:5c
Sending on   Socket/fallback
DHCPDISCOVER on eth1 to 255.255.255.255 port 67 interval 3
DHCPOFFER of 192.168.1.78 from 192.168.1.254
DHCPREQUEST of 192.168.1.78 on eth1 to 255.255.255.255 port 67
DHCPACK of 192.168.1.78 from 192.168.1.254
NetworkManager: <info>  DHCP: device eth1 state changed preinit -> bound
NetworkManager: <info>  Activation (eth1) Stage 4 of 5 (IP Configure Get) scheduled...
NetworkManager: <info>  Activation (eth1) Stage 4 of 5 (IP Configure Get) started...
NetworkManager: <info>    address 192.168.1.78
NetworkManager: <info>    prefix 24 (255.255.255.0)
NetworkManager: <info>    gateway 192.168.1.254
NetworkManager: <info>    nameserver '192.168.1.254'
NetworkManager: <info>    domain name 'lan'
NetworkManager: <info>  Activation (eth1) Stage 5 of 5 (IP Configure Commit) scheduled...
NetworkManager: <info>  Activation (eth1) Stage 4 of 5 (IP Configure Get) complete.
NetworkManager: <info>  Activation (eth1) Stage 5 of 5 (IP Configure Commit) started...
bound to 192.168.1.78 -- renewal in 33273 seconds.
NetworkManager: <info>  Policy set 'Auto Mobile Broadband (CDMA) connection' (ppp0) as default for routing and DNS.
NetworkManager: <info>  (eth1): device state change: 7 -> 8
NetworkManager: <debug> [1267227525.621535] periodic_update(): Roamed from BSSID 00:21:29:E4:BB:91 (2TIVO2) to (none) ((none))
NetworkManager: <info>  Policy set 'Auto 2TIVO2' (eth1) as default for routing and DNS.
NetworkManager: <info>  Activation (eth1) successful, device activated.
NetworkManager: <info>  Activation (eth1) Stage 5 of 5 (IP Configure Commit) complete.

^CNetworkManager: <WARN>  nm_signal_handler(): Caught signal 2, shutting down normally.
NetworkManager: <info>  (eth0): now unmanaged
NetworkManager: <info>  (eth0): device state change: 2 -> 1
NetworkManager: <info>  (eth0): cleaning up...
NetworkManager: <info>  (eth0): taking down device.
NetworkManager: <info>  Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889)
NetworkManager: <info>  (eth1): now unmanaged
NetworkManager: <info>  (eth1): device state change: 8 -> 1
NetworkManager: <info>  (eth1): deactivating device (reason: 36).
NetworkManager: <info>  eth1: canceled DHCP transaction, dhcp client pid 6816
NetworkManager: <WARN>  nm_device_wifi_disable_encryption(): error setting key for device eth1: Invalid argument
-- Error received: Numerical result out of range
-- Original message: type=0x19 length=56 flags=<REQUEST,ACK> sequence-nr=1267227500 pid=4200967
NetworkManager: <WARN>  check_one_route(): (eth1) error -34 returned from rtnl_route_del(): Sucess

NetworkManager: <info>  (eth1): cleaning up...
NetworkManager: <info>  (eth1): taking down device.
NetworkManager: <info>  Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889)
NetworkManager: <info>  (ttyUSB0): now unmanaged
NetworkManager: <info>  (ttyUSB0): device state change: 8 -> 1
NetworkManager: <info>  (ttyUSB0): deactivating device (reason: 36).
NetworkManager: <debug> [1267227861.271254] nm_serial_device_close(): Closing device 'ttyUSB0'
NetworkManager: nm_system_device_flush_ip4_routes_with_iface: assertion `iface_idx >= 0' failed
NetworkManager: nm_system_device_flush_ip4_addresses_with_iface: assertion `iface_idx >= 0' failed
NetworkManager: <info>  (ttyUSB0): cleaning up...
NetworkManager: <info>  (ttyUSB0): taking down device.
NetworkManager: <info>  Unmanaged Device found; state CONNECTED forced. (see http://bugs.launchpad.net/bugs/191889)
NetworkManager: <info>  exiting (success)
anna dell10:~$ ls

/.
/etc
/etc/dbus-1
/etc/dbus-1/event.d
/etc/dbus-1/system.d
/etc/dbus-1/system.d/NetworkManager.conf
/etc/dbus-1/system.d/nm-dhcp-client.conf
/etc/dbus-1/system.d/nm-dispatcher.conf
/etc/dbus-1/system.d/nm-system-settings.conf
/etc/dbus-1/system.d/nm-avahi-autoipd.conf
/etc/NetworkManager
/etc/NetworkManager/dispatcher.d
/etc/NetworkManager/dispatcher.d/01ifupdown
/etc/NetworkManager/system-connections
/etc/NetworkManager/nm-system-settings.conf
/etc/init.d
/etc/init.d/NetworkManager
/var
/var/lib
/var/lib/NetworkManager
/usr
/usr/share
/usr/share/gnome-vpn-properties
/usr/share/doc
/usr/share/doc/network-manager
/usr/share/doc/network-manager/README.Debian
/usr/share/doc/network-manager/copyright
/usr/share/doc/network-manager/NEWS.Debian.gz
/usr/share/man
/usr/share/man/man1
/usr/share/man/man1/nm-tool.1.gz
/usr/share/man/man1/nm-vpn-properties.1.gz
/usr/share/man/man8
/usr/share/man/man8/NetworkManager.8.gz
/usr/share/dbus-1
/usr/share/dbus-1/system-services
/usr/share/dbus-1/system-services/org.freedesktop.nm_dispatcher.service
/usr/share/dbus-1/system-services/org.freedesktop.NetworkManagerSystemSettings.service
/usr/share/NetworkManager
/usr/share/NetworkManager/gdb-cmd
/usr/share/PolicyKit
/usr/share/PolicyKit/policy
/usr/share/PolicyKit/policy/org.freedesktop.network-manager-settings.system.policy
/usr/share/apport
/usr/share/apport/package-hooks
/usr/share/apport/package-hooks/source_network-manager.py
/usr/sbin
/usr/sbin/NetworkManager
/usr/sbin/nm-system-settings
/usr/lib
/usr/lib/NetworkManager
/usr/lib/NetworkManager/nm-crash-logger
/usr/lib/NetworkManager/nm-dhcp-client.action
/usr/lib/NetworkManager/nm-dispatcher.action
/usr/lib/NetworkManager/nm-avahi-autoipd.action
/usr/lib/NetworkManager/libnm-settings-plugin-keyfile.so
/usr/lib/NetworkManager/libnm-settings-plugin-keyfile.la
/usr/lib/NetworkManager/libnm-settings-plugin-keyfile.a
/usr/lib/NetworkManager/libnm-settings-plugin-ifupdown.so
/usr/lib/NetworkManager/libnm-settings-plugin-ifupdown.la
/usr/lib/NetworkManager/libnm-settings-plugin-ifupdown.a
/usr/lib/pppd
/usr/lib/pppd/2.4.4
/usr/lib/pppd/2.4.4/nm-pppd-plugin.so
/usr/lib/pppd/2.4.5
/usr/lib/pppd/2.4.5/nm-pppd-plugin.so
/usr/lib/network-manager
/usr/lib/network-manager/ifblacklist_migrate.sh
/usr/bin
/usr/bin/nm-tool
/lib
/lib/udev
/lib/udev/nm-modem-probe
/lib/udev/rules.d
/lib/udev/rules.d/77-nm-probe-modem-capabilities.rules
/usr/share/doc/network-manager/AUTHORS
/usr/share/doc/network-manager/TODO
/usr/share/doc/network-manager/README.gz
/usr/share/doc/network-manager/changelog.Debian.gz
/usr/share/apport/package-hooks/source_network-manager-applet.py

P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB0
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB0
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB0/tty/ttyUSB0
N: ttyUSB0
S: serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port0
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB0/tty/ttyUSB0
E: DEVNAME=/dev/ttyUSB0
E: ID_MODEL=Sierra_Wireless_USB_598
E: ID_MODEL_ENC=Sierra\x20Wireless\x20USB\x20598
E: ID_SERIAL=Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________
E: ID_USB_INTERFACES=:ffffff:080650:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=sierra
E: NM_MODEM_USB_INTERFACE_NUMBER=00
E: DEVLINKS=/dev/char/188:0 /dev/serial/by-path/pci-0000:00:1d.0-usb-0:2:1.0-port0 /dev/serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port0
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB1
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB1
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB1/tty/ttyUSB1
N: ttyUSB1
S: serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port1
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB1/tty/ttyUSB1
E: DEVNAME=/dev/ttyUSB1
E: ID_MODEL=Sierra_Wireless_USB_598
E: ID_MODEL_ENC=Sierra\x20Wireless\x20USB\x20598
E: ID_SERIAL=Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________
E: ID_USB_INTERFACES=:ffffff:080650:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=sierra
E: NM_MODEM_USB_INTERFACE_NUMBER=00
E: DEVLINKS=/dev/char/188:1 /dev/serial/by-path/pci-0000:00:1d.0-usb-0:2:1.0-port1 /dev/serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port1
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB2
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB2
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB2/tty/ttyUSB2
N: ttyUSB2
S: serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port2
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB2/tty/ttyUSB2
E: DEVNAME=/dev/ttyUSB2
E: ID_MODEL=Sierra_Wireless_USB_598
E: ID_MODEL_ENC=Sierra\x20Wireless\x20USB\x20598
E: ID_SERIAL=Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________
E: ID_USB_INTERFACES=:ffffff:080650:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=sierra
E: NM_MODEM_USB_INTERFACE_NUMBER=00
E: DEVLINKS=/dev/char/188:2 /dev/serial/by-path/pci-0000:00:1d.0-usb-0:2:1.0-port2 /dev/serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port2
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB3
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB3
P: /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB3/tty/ttyUSB3
N: ttyUSB3
S: serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port3
E: DEVPATH=/devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/ttyUSB3/tty/ttyUSB3
E: DEVNAME=/dev/ttyUSB3
E: ID_MODEL=Sierra_Wireless_USB_598
E: ID_MODEL_ENC=Sierra\x20Wireless\x20USB\x20598
E: ID_SERIAL=Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________
E: ID_USB_INTERFACES=:ffffff:080650:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=sierra
E: NM_MODEM_USB_INTERFACE_NUMBER=00
E: DEVLINKS=/dev/char/188:3 /dev/serial/by-path/pci-0000:00:1d.0-usb-0:2:1.0-port3 /dev/serial/by-id/usb-Sierra_Wireless__Incorporated_Sierra_Wireless_USB_598__4Vx________-if00-port3
E: ID_USB_INTERFACES=:ffffff:080650:
E: ID_USB_INTERFACE_NUM=01
E: ID_USB_DRIVER=usb-storage
E: ID_USB_INTERFACES=:0e0100:0e0200:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=uvcvideo
E: ID_USB_INTERFACES=:0e0100:0e0200:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=uvcvideo
E: ID_USB_INTERFACES=:080650:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=usb-storage

Bus 003 Device 002: ID 413c:02b0 Dell Computer Corp. 
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. Mass Stroage Device
Bus 001 Device 003: ID 064e:a118 Suyin Corp. 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 005: ID 1199:0025 Sierra Wireless, Inc. 
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

[Date Prev][Date Next] [Thread Prev][Thread Next] [Thread Index] [Date Index] [Author Index]