Re: The issue "ionice: execvp failed: No such file or directory" once more.

[Hongyi Zhao <hongyi zhao gmail com>]

On 11/06/2012 08:52 PM, Jean Brefort wrote:
> Debian squeeze is shipped with util-linux-2.17.2 which
> contains /usr/bin/ionice, so it should be already on your system.
> Installing a newer version might be not a so good idea. Just check that
> util-linux is installed (it should). If /usr/bin/ionice does not exists,
> reinstall that package, your system is most probably broken.
I've got;-)

In fact, the issue is cause by the git clone within jhbuild for my last 
compiling process.

In detail,  when I running the following command:

$ jhbuild -f jhbuildrc-gnome3 buildone yelp-xsl

the jhbuild will invoke the git to clone the source of yelp-xsl, but the 
jhbuild failed to do this step.  I don't know the reason.

I just run the following command separately:

$ git clone git://git.gnome.org/yelp-xsl

And then, I copied the source to directory for jhbuild to use.  then the 
following command will be OK:

$ jhbuild -f jhbuildrc-gnome3 buildone yelp-xsl


Regards



> Le mardi 06 novembre 2012 à 20:36 +0800, Hongyi Zhao a écrit :
> > On 11/06/2012 05:39 PM, Jean Brefort wrote:
> > > ionice is part of util-linux-ng. Check your installation.
> > > Regards,
> > > Jean
> > According to your above advice, I do the following thing:
> >
> > $ git clone git://gitorious.org/util-linux-ng/util-linux-ng.git
> > werner@debian-asus:~/util-linux-ng$ ./autogen.sh
> > werner@debian-asus:~/util-linux-ng$ ./configure --prefix=/usr/local &&
> > make && sudo make install
> >
> > Then, I put the following line into my config file  jhbuildrc-gnome3 for
> > jhbuild:
> >
> > addpath('PKG_CONFIG_PATH', '/usr/local/lib/pkgconfig')
> >
> > Now, I rerun the jhbuild with the following command but failed again,
> > see the following for detail:
> >
> >
> > -------------
> > $ jhbuild -f jhbuildrc-gnome3 buildone yelp-xsl
> > *** Checking out yelp-xsl *** [1/1]
> > git remote set-url origin git://git.gnome.org/yelp-xsl
> > git remote update origin
> > Fetching origin
> > *** Configuring yelp-xsl *** [1/1]
> > ./autogen.sh --prefix /opt/jhbuild/gnome --libdir
> > '/opt/jhbuild/gnome/lib64'  --disable-maintainer-mode --disable-static
> > --disable-gtk-doc
> > ionice: executing ./autogen.sh failed: No such file or directory
> > *** Error during phase configure of yelp-xsl: ########## Error running
> > ./autogen.sh --prefix /opt/jhbuild/gnome --libdir
> > '/opt/jhbuild/gnome/lib64'  --disable-maintainer-mode --disable-static
> > --disable-gtk-doc  *** [1/1]
> >
> >     [1] Rerun phase configure
> >     [2] Ignore error and continue to build
> >     [3] Give up on module
> >     [4] Start shell
> >     [5] Reload configuration
> >     [6] Go to phase "wipe directory and start over"
> >     [7] Go to phase "clean"
> >     [8] Go to phase "distclean"
> > choice:
> > -----------------
> >
> > As you can see, this time, I meet the error as "ionice: executing
> > ./autogen.sh failed: No such file or directory"
> >
> > Any hints on this issue?
> >
> > Regards
> >
> > > Le mardi 06 novembre 2012 à 15:56 +0800, Hongyi Zhao a écrit :
> > > > Hi all,
> > > >
> > > > I've post a message on this type of issue.  Now, I meet it again, sigh;-(
> > > >
> > > > See the following code:
> > > >
> > > > --------------
> > > > werner@debian-asus:~$ jhbuild -f jhbuildrc-gnome3 build -a --nodeps yelp-xsl
> > > > -------------------
> > > >
> > > > Then I meet the following errors:
> > > >
> > > > -------------
> > > > [snipped]
> > > > *** Configuring yelp-xsl *** [7/7]
> > > > ./autogen.sh --prefix /opt/jhbuild/gnome --libdir
> > > > '/opt/jhbuild/gnome/lib64'  --disable-maintainer-mode --disable-static
> > > > --disable-gtk-doc
> > > > ionice: execvp failed: No such file or directory
> > > > *** Error during phase configure of yelp-xsl: ########## Error running
> > > > ./autogen.sh --prefix /opt/jhbuild/gnome --libdir
> > > > '/opt/jhbuild/gnome/lib64'  --disable-maintainer-mode --disable-static
> > > > --disable-gtk-doc  *** [7/7]
> > > >
> > > >      [1] Rerun phase configure
> > > >      [2] Ignore error and continue to build
> > > >      [3] Give up on module
> > > >      [4] Start shell
> > > >      [5] Reload configuration
> > > >      [6] Go to phase "wipe directory and start over"
> > > >      [7] Go to phase "clean"
> > > >      [8] Go to phase "distclean"
> > > > choice: ^CInterrupted
> > > > -----------------
> > > >
> > > > Below is the content of the config file jhbuildrc-gnome3:
> > > >
> > > > ---------------
> > > > # -*- mode: python -*-
> > > > # -*- coding: utf-8 -*-
> > > > import os
> > > > import sys
> > > >
> > > > checkoutroot = os.path.expanduser('/opt/jhbuild/checkout/gnome')
> > > > prefix = os.path.expanduser('/opt/jhbuild/gnome')
> > > >
> > > > autogenargs='--disable-maintainer-mode --disable-static --disable-gtk-doc'
> > > >
> > > > addpath('PKG_CONFIG_PATH', '/usr/lib/pkgconfig')
> > > > addpath('PKG_CONFIG_PATH', '/usr/share/pkgconfig')
> > > > ---------------------
> > > >
> > > > Any hints on this issue?  Thanks in advance.
> > > >
> > > > Regards


--
.: Hongyi Zhao [ hongyi.zhao AT gmail.com ] Free as in Freedom :.