NM & ath0 trouble



hi, 

i have not been able to use NM for a while now due to issues described
in my 2005-October/msg00208.html post (any reason why there was no
response to that?). here's another (unsuccessful) try using the new
madwifi driver...

i'd like to use NM again, so any hints or comments. i'm running FC4 with
NetworkManager-0.5.1-1.FC4.4
dhcdbd-1.9-1.FC4
wireless-tools-28-0.pre10.4
dhcp-3.0.2-28.FC4

NM is trying to connect to an open network but fails...

here's the output from "NetworkManager --no-daemon":
NetworkManager: <information>   ath0: Device is fully-supported using
driver 'ath_pci'.
NetworkManager: <information>   nm_device_new(): waiting for device's
worker thread to start
NetworkManager: <information>   nm_device_new(): device's worker thread
started, continuing.
NetworkManager: <information>   Now managing wireless device 'ath0'.
NetworkManager: <information>   Deactivating device ath0.
NetworkManager: <information>   eth0: Device is fully-supported using
driver 'e100'.
NetworkManager: <information>   nm_device_new(): waiting for device's
worker thread to start
NetworkManager: <information>   nm_device_new(): device's worker thread
started, continuing.
NetworkManager: <information>   Now managing wired device 'eth0'.
NetworkManager: <information>   Deactivating device eth0.
NetworkManager: <information>   Updating allowed wireless network lists.
NetworkManager: <information>   FORCE: device
'/org/freedesktop/NetworkManager/Devices/ath0', network 'default'
NetworkManager: <information>   Deactivating device ath0.
NetworkManager: <debug info>    [1136423147.346090]  (): Forcing AP
'default'
NetworkManager: <information>   Device ath0 activation scheduled...
NetworkManager: <information>   Activation (ath0) started...
NetworkManager: <information>   Activation (ath0) Stage 1 (Device
Prepare) scheduled...
NetworkManager: <information>   Activation (ath0) Stage 1 (Device
Prepare) start
ed...
NetworkManager: <information>   Activation (ath0) Stage 2 (Device
Configure) scheduled...
NetworkManager: <information>   Activation (ath0) Stage 1 (Device
Prepare) complete.
NetworkManager: <information>   Activation (ath0) Stage 2 (Device
Configure) starting...
NetworkManager: <information>   Activation (ath0/wireless) Stage 2
(Device Configure) will connect to access point 'default'.
NetworkManager: <information>   Activation (ath0/wireless): access point
'default' is unencrypted, no key needed.
NetworkManager: <information>   Activation (ath0/wireless): using essid
'default', with no authentication.
NetworkManager: <debug info>    [1136423162.703110]  (): Activation
(ath0/wireless): no hardware link to 'default' in non-encrypted mode.
NetworkManager: <information>   Activation (ath0) failure scheduled...
NetworkManager: <information>   Activation (ath0) failure scheduled...
NetworkManager: <information>   Activation (ath0) Stage 2 (Device
Configure) complete.
NetworkManager: <information>   Activation (ath0) failed for access
point (default)
NetworkManager: <information>   Deactivating device ath0.
NetworkManager: <information>   Activation (ath0) failed for access
point (default)
NetworkManager: <information>   Deactivating device ath0.


and in /var/log/messages:
dhcdbd: message_handler: message handler not found
under /com/redhat/dhcp/ath0 for sub-path ath0.dbus.get.reason


driver info from "dmesg":

ath_hal: 0.9.16.13 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413, DFS)
ath_rate_sample: 1.2
ath_pci: 0.9.4.5 (Atheros/multi-bss)
ACPI: PCI Interrupt 0000:02:0a.0[A] -> Link [LNKH] -> GSI 11 (level,
low) -> IRQ 11
wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps
24Mbps 36Mbps 48Mbps 54Mbps
wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps
54Mbps
wifi0: H/W encryption support: WEP AES AES_CCM TKIP
wifi0: mac 5.6 phy 4.1 5ghz radio 1.7 2ghz radio 2.3
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Atheros 5212: mem=0xfcee0000, irq=11





[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]