[Ekiga-list] Timeout? Call out OK call in from Diamon unseen or broken

[Damien Sandras]

Le lundi 22 octobre 2007 à 14:19 +0100, Philippe Laliberte a écrit :
> Damien Sandras wrote:
> > Le lundi 22 octobre 2007 à 11:52 +0100, Philippe Laliberte a écrit :
> >   
> >> ael wrote: 
> >>     
> >>> P laliberte wrote:
> >>>   
> >>>       
> >>>> ael wrote:
> >>>>     
> >>>>         
> >>>>> Philippe Laliberte wrote:
> >>>>>  
> >>>>>       
> >>>>>           
> >>>>>> Hello,
> >>>>>>
> >>>>>> I am running into a little problem. I did dig into the wiki but to no
> >>>>>> avail.
> >>>>>>
> >>>>>> Set-up:
> >>>>>>
> >>>>>> Fedora 7.
> >>>>>> kernel-2.6.22.9
> >>>>>> Firewall disabled. selinux disabled
> >>>>>> Ekiga 2.0.11
> >>>>>>
> >>>>>> Router Modem ADSL SpeedTouch 780
> >>>>>> Firewall disabled (once I get Ekiga working I'll test what I can close)
> >>>>>> VoIp turned off
> >>>>>>
> >>>>>> Modem routing Configuration
> >>>>>>
> >>>>>> Protocol    Port Range    Translate To ...    Trigger Protocol  
> >>>>>> Trigger Port   Any            5000 - 5100    5000 - 5100      
> >>>>>> -                               -
> >>>>>> UDP           3479 - 3479    3479 - 3479   
> >>>>>> UDP                         3479
> >>>>>> UDP           3478 - 3479    3478 - 3479   
> >>>>>> UDP                         3478
> >>>>>>     
> >>>>>>         
> >>>>>>             
> >>>>> I can't quite decode the above. If you trigger on 3478 (UDP) and then
> >>>>> open 5000 -5100 (UDP) then it should be ok. I am not sure that is what
> >>>>> you have above is it? I can't make out the first line ending in
> >>>>> 5000-5100: how does that relate to the two following lines?
> >>>>>
> >>>>> ael
> >>>>> _______________________________________________
> >>>>> ekiga-list mailing list
> >>>>> ekiga-list at gnome.org
> >>>>> http://mail.gnome.org/mailman/listinfo/ekiga-list
> >>>>>   
> >>>>>       
> >>>>>           
> >>>> Just missing a cariage return
> >>>>
> >>>> Protocol    Port Range    Translate To ...    Trigger Protocol  Trigger
> >>>> Port   Any            5000 - 5100    5000 - 5100    -    -
> >>>> UDP           3479 - 3479    3479 - 3479    UDP   3479
> >>>> UDP           3478 - 3479    3478 - 3479    UDP   3478
> >>>>
> >>>>
> >>>> What you mean is that I should just do :
> >>>>
> >>>> UDP         5000 - 5100    3479 - 3479    UDP   3479
> >>>> UDP         5100 - 5100    3478 - 3479    UDP   3478
> >>>>     
> >>>>         
> >>> Looking at that again, why are you translating 3479 into 5000-5100? Or
> >>> am I misunderstanding the web interface (I assume)?
> >>>
> >>> Once you see a packet on 3478, then open 5000-5100. Do not translate
> >>> 3478 into 5000... if that is what the above means. 3478 and 3479 should
> >>> be (con) tracked properly by the router. It is just that it will block
> >>> 5000-5100 unless it is told otherwise.
> >>>
> >>> I have not encountered a SpeedTouch router so I may be misunderstanding
> >>> its configuration.
> >>>
> >>> ael
> >>>   
> >>>       
> >> The error is mine, late doing too many thing at the same time. You did
> >> understand it correctly the first time. 
> >>
> >> UDP         5000 - 5100    5000 - 5100    UDP   3479
> >> UDP         5100 - 5100    5000 - 5100    UDP   3478
> >> I'll test it later this afternoon thanks.
> >>
> >>     
> >
> > Why 5100 - 5100 ?
> >
> >   
> 
> Well unconclusive:
> 
> UDP    5000 - 5100    5000 - 5100    UDP    3479
> UDP    5000 - 5100    5000 - 5100    UDP    3478
> 
> 
> Wizard, still in symetric NAT
> 
> Manual STUN: No sound on 500 at ekiga.net, no calls in from Diamoncard even 
> after a fresh restart
> None: 500 at ekiga.net ok, no calls in from Diamoncard even after a fresh 
> restart.
> 
> 
> Back to no trigger definition, same as above.
> 
> Back to TCP/UDP
> 
> Any    5000 - 5100    5000 - 5100    Any    3478
> Any    5000 - 5100    5000 - 5100    Any    3479
> 
> Wizard, still in symetric NAT
> 
> STUN: No sound on 500 at ekiga.net, Calls in from Diamoncard OK even after 
> a while, after manual changes back and forth it does not work anymore
> 
> None: 500 at ekiga.net ok, no calls in from Diamoncard even after a fresh 
> restart.
> 
> Back to no trigger definition, same as above.
> 
> Wireshark shows SIP activity for the 500 at ekiga call but nothing coming 
> in from Diamoncard.
> 
> Can all this working not working be related to a slowness from 
> diamoncard or the router to react to changes? I am connected to 
> eugw.ast.diamondcard.us. If I try to setup my VoIp on the modem, it 
> never seems to register.
> 
> I'll go back to STUN (with trigger of the router) and shutdown Ekiga for 
> an hour or so to see if when I come back It will work.
> 

In my opinion, the problem lies in the configuration of your router.
There is relatively few that we can do.

If it detects symmetric NAT, that is probably because the port
forwarding does not work appropriately.
-- 
 _     Damien Sandras
(o-      
//\    Ekiga Softphone : http://www.ekiga.org/
v_/_   NOVACOM         : http://www.novacom.be/
       FOSDEM          : http://www.fosdem.org/
       SIP Phone       : sip:dsandras at ekiga.net