[Ekiga-list] Timeout? Call out OK call in from Diamon unseen or broken

[Damien Sandras]

Le lundi 22 octobre 2007 à 11:52 +0100, Philippe Laliberte a écrit :
> ael wrote: 
> > P laliberte wrote:
> >   
> > > ael wrote:
> > >     
> > > > Philippe Laliberte wrote:
> > > >  
> > > >       
> > > > > Hello,
> > > > > 
> > > > > I am running into a little problem. I did dig into the wiki but to no
> > > > > avail.
> > > > > 
> > > > > Set-up:
> > > > > 
> > > > > Fedora 7.
> > > > > kernel-2.6.22.9
> > > > > Firewall disabled. selinux disabled
> > > > > Ekiga 2.0.11
> > > > > 
> > > > > Router Modem ADSL SpeedTouch 780
> > > > > Firewall disabled (once I get Ekiga working I'll test what I can close)
> > > > > VoIp turned off
> > > > > 
> > > > > Modem routing Configuration
> > > > > 
> > > > > Protocol    Port Range    Translate To ...    Trigger Protocol  
> > > > > Trigger Port   Any            5000 - 5100    5000 - 5100      
> > > > > -                               -
> > > > > UDP           3479 - 3479    3479 - 3479   
> > > > > UDP                         3479
> > > > > UDP           3478 - 3479    3478 - 3479   
> > > > > UDP                         3478
> > > > >     
> > > > >         
> > > > I can't quite decode the above. If you trigger on 3478 (UDP) and then
> > > > open 5000 -5100 (UDP) then it should be ok. I am not sure that is what
> > > > you have above is it? I can't make out the first line ending in
> > > > 5000-5100: how does that relate to the two following lines?
> > > > 
> > > > ael
> > > > _______________________________________________
> > > > ekiga-list mailing list
> > > > ekiga-list at gnome.org
> > > > http://mail.gnome.org/mailman/listinfo/ekiga-list
> > > >   
> > > >       
> > > Just missing a cariage return
> > > 
> > > Protocol    Port Range    Translate To ...    Trigger Protocol  Trigger
> > > Port   Any            5000 - 5100    5000 - 5100    -    -
> > > UDP           3479 - 3479    3479 - 3479    UDP   3479
> > > UDP           3478 - 3479    3478 - 3479    UDP   3478
> > > 
> > > 
> > > What you mean is that I should just do :
> > > 
> > > UDP         5000 - 5100    3479 - 3479    UDP   3479
> > > UDP         5100 - 5100    3478 - 3479    UDP   3478
> > >     
> > 
> > Looking at that again, why are you translating 3479 into 5000-5100? Or
> > am I misunderstanding the web interface (I assume)?
> > 
> > Once you see a packet on 3478, then open 5000-5100. Do not translate
> > 3478 into 5000... if that is what the above means. 3478 and 3479 should
> > be (con) tracked properly by the router. It is just that it will block
> > 5000-5100 unless it is told otherwise.
> > 
> > I have not encountered a SpeedTouch router so I may be misunderstanding
> > its configuration.
> > 
> > ael
> >   
> The error is mine, late doing too many thing at the same time. You did
> understand it correctly the first time. 
> 
> UDP         5000 - 5100    5000 - 5100    UDP   3479
> UDP         5100 - 5100    5000 - 5100    UDP   3478
> I'll test it later this afternoon thanks.
> 

Why 5100 - 5100 ?

-- 
 _     Damien Sandras
(o-      
//\    Ekiga Softphone : http://www.ekiga.org/
v_/_   NOVACOM         : http://www.novacom.be/
       FOSDEM          : http://www.fosdem.org/
       SIP Phone       : sip:dsandras at ekiga.net